John Deere RT 1370 WR - Manuals

1 3 2 5 4 MACHINE SAFETY LABELS AND POSITIONS Safety Signs - Page 6 4 5 2 3 3 2 1 1 2 3 1 1

MACHINE SAFETY LABELS AND POSITIONS MAX Kg... 6 GREASE 7 OIL LEVEL 8 OIL 9 OIL 10 540 MAX 11 6) Coupling point for lifting (indicating the maximun capacity)7) Greasing point8) Oil level plug9) Oil drain plug 10) Oil fill plug11) Number of revolutions of power takeoff Safety Signs - Page 7 11 9 10 8 ...

Preparing the tractor CAUTION: Avoid injury. Proper ballastings is required for safe operation of your tiller IMPORTANT: Refer to the tractor operator manual for proper ballasting information and tire inflation • A 540 rpm PTO• Refer to the tractor operator manual for correct ballasting and tire pre...

INSTALLING Installing - Page 9 IMPORTANT: Tiller MUST BE level front to rear. • Engage the cardan shaft and check that it is perfectly locked on the tractor PTO (G). Check that the guard(H) is free to turn and fix it with the relative latch. 4. Raise tiller. 5. Remove spring locking pin (K) from par...

Park vehicle safely • Stop vehicle on a level surface, not on a slope. • Disengage PTO. • Engage the park brake. • STOP the engine. • Remove the key. • Before you leave the operator’s seat, wait for engine and all moving parts to STOP. Stay clear of rotating drivelines Entanglement in rotating drive...

REMOVING Removing - Page 11 A C B Removing tiller with Quick Coupler 1. Raise tiller.2. Put parking stand (A) in the DOWN position: Install spring locking pin (C) in order to secure parkingstand (A) to the tiller bracket (B). 3. Lower tiller to the ground.4. Disconnect driveline from tractor by pull...

OPERATING Operating - Page 12 • Clear work area of objects that you do not want tilled into the ground or that might damage the tiller. Con- sider the tilling area and set up a safe tilling pattern. Do not till under condition in which traction or stability is doubtful. Keep people and pets out of t...

Raising parking stand 1. Remove spring locking pin (C). 2. Slide parking stand (A) and way up on tiller bracket (B). 3. Fasten with spring locking pin (C). Lowering parking stand 1. Remove spring locking pin (C). 2. Slide parking stand (A) and put down on tiller bracket (B).3. Install spring locking...

OPERATING Leveling tiller (front-to-rear) 1. Start the engine.2. Lower the tiller to 25 mm (1 in.) off the ground.3. Stop the engine.4. Make sure the top of the tiller is LEVEL, or PARALLEL with the ground, front-to-rear. 5. Adjust level, if necessary. To adjust level: a. Start the engine.b. Lower t...

OPERATING Adjusting leveling board Besides supporting the levelling plate and acting as ashock absorber for it during road transport, the springram (1) prevents the machine from overturning whenparking.To adjust the spring pre-loading, screw or unscrew theupper nut (2) using the spring adjuster.The ...

SERVICE MACHINE SAFELY Service Machine Safely - Page 17 Practice safe maintenance • Understand service procedure before doing work. Keep area clean and dry. • Never lubricate, service, or adjust machine while it is moving. Keep safety devices in place and in working condition. Keep hardware tight. •...

Service lubrication WARNING: • Firmly block tiller on horizontal surface. • Always keep oils and greases well away from children’s reach.• Always thoroughly read the warnings and precautions indicated on the containers. Avoid contact with the skin. • Always thoroughly and fully wash after use. The u...

SERVICE LUBRICATION Service Lubrication - Page 19 C Greasing and lubricant points C) Rotor spindle lubricatorD) Reduction unit oil plugE) Transmission oil fill plugF) Transmission oil drain plugG) Transmission oil level plugH) Hoe blades fixing bolts Lubricants • It is advisable to use SAE 85W/140 O...

SERVICE Service - Page 20 Replacing tines CAUTION: To prevent injuri: Wear heavy gloves when replacing tines. To get the best performance from your tiller:• Replace badly bent, worn, or broken tines immediatly.• Replace worn or broken hardware (see your Frontier dealer for correct hardware).• MAKE S...

TROUBLESHOOTING Using troubleshooting chart If you are experiencing a problem that is not listed in this chart, see your Frontier dealer for service.When you have checked all the possible causes listed and you are still experiencing the problem, seeyour Frontier dealer. IF CHECK EXCESSIVE TINE WEAR ...

STORING MACHINE Storing Machine - Page 22 Storing tiller CAUTION: Before you work around hitch: • STOP engine.• LOCK park brake.• FIRMLY block tiller on horizontal surface. 1. Put parking stand in the DOWN position (See Lowering Parking Stand in the Operating Tiller section). 2. Disconnect tiller fr...

CAUTION: FIRMLY block tiller on horizontal surface. Installing parking stand (phase 1, operating 1. Only skid version) 1) Put parking stand (A) and fasten bolts (B) and nuts (C). Tighten lock nuts to the requested tightening torque. Installing all assy against overturning (phase 1, operation 2. Roll...

PHASE 1 (Only skid version) PHASE 2 (Roller and skid version) Assembly - Page 24 ASSEMBLY H M I D D A C B D E G F F L E C A B G OPERATION 1 OPERATION 2 OPERATION 2 OPERATION 1

PHASE 3 Assembly - Page 25 ASSEMBLY F H E A C B I D H E C A D I O M N L Q R P M N G

• Means of dispatch. If this item is not indicated, the Manufacturer, while dedicating particular care to this service, shall not be held responsible for delays in delivery caused by cases of force majeure.Transport expenses shall always be at the consignee’s charge. The goods travel at the purchase...

WARRANTY Warranty - Page 27 MASCHIO S.p.A. warrants this product to be free from defect in material and workmanship. Except as otherwise set forth below, theduration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE PROD-UCT TO THE ORIGINAL PURCHASER. Under n...

MASCHIO S.p.A. warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from thedate of delivery of the product to the original purchaser. Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of MASC...