John Deere MTF051056L - Manuals

Page 2 - INTRODUCTION; Registration of the warranty is; RESPONSIBILITY OF THE OWNER; Read And Keep This Book For; PRODUCT INFORMATION; This information includes the; INSTRUCTION BOOKS; and the; WARRANTIES; . This information must be included to make

INTRODUCTION 2 MTF − 051056L Congratulations on your purchase of a Frontier Snowthrower. It has been designed, engineered and manufactured to give youthe best possible dependability and performance. However, like all mechanical products, your machine will occasionally re-quire adjustment and mainten...

Page 3 - RULES FOR SAFE OPERATION; Hazard Symbols and the meanings

RULES FOR SAFE OPERATION 3 MTF − 051056L This manual contains safety information to make youaware of the hazards and risks associated with snow throwers, and how to avoid them. The snow thrower is designed andintended for removal of snow, and should not be used for any otherpurpose. It is important ...

Page 6 - TABLE OF CONTENTS

TABLE OF CONTENTS 6 MTF − 051056L HAZARD SYMBOLS AND THE MEANINGS 3 . . . . . . . . . . . . . . . . . . . . . . . OPERATING SYMBOLS AND THEIR MEANINGS 3 . . . . . . . . . . . . . . . . . . SAFETY DECALS 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WAR...

Page 7 - SAFETY DECALS; Look for this symbol to indicate important safe-; Identifying Your Snowthrower

SAFETY DECALS 7 MTF − 051056L WARNING: If safety decals are dam- aged or missing, replace immediately. Look for this symbol to indicate important safe- ty precautions. This symbol indicates: “Atten- tion! Become Alert! Your Safety Is At Risk.” Before operation of your snowthrower, read the safety de...

Page 8 - OWNER’S INFORMATION; THREE YEAR LIMITED WARRANTY; FOR YOUR RECORDS

OWNER’S INFORMATION MTF − 051056L 8 THREE YEAR LIMITED WARRANTY Murray warrants to the original purchaser of this Frontier Branded Snowthrower that this unit shall be free from defects inmaterial and workmanship under normal use and service for a period of Three (3) Year from the date of purchase; h...

Page 9 - ASSEMBLY; TOOLS REQUIRED FOR ASSEMBLY; HOW TO MEASURE SCREW SIZE; CONTENTS OF SHIPPING CARTON; WARNING: Always wear safety glasses or eye

ASSEMBLY 9 MTF − 051056L TOOLS REQUIRED FOR ASSEMBLY 1 − Knife 2 − 1/2” wrenches (or adjustable wrenches) 2 − 9/16” wrenches (or adjustable wrenches) 2 − 3/4” wrenches (or adjustable wrenches) 1 − 3/8” wrenches (or adjustable wrenches) 1 − Pair pliers or screw driver (to spread cotter pin) HOW TO ME...

Page 10 - UNPACKING

ASSEMBLY 10 MTF − 051056L Figure 2 shows the snowthrower in the shipping position. Figure 3 shows the snowthrower completely assembled. Reference to right and left hand side of the snowthrower is from the operator’s position at the handle. UNPACKING 1. Locate the two tear tabs at the bottom of the c...

Page 11 - UPPER HANDLE AND CRANK ASSEMBLY; NOTE: Make sure the cables are not caught between; CHECK THE CABLES

ASSEMBLY 11 MTF − 051056L UPPER HANDLE AND CRANK ASSEMBLY 1. Loosen, but do not remove the screws, flatwashers, lock- washers and hex nuts in the upper holes of the lower han- dle. 2. Remove the fasteners and the crank assembly eyebolt from the lower holes of the lower handle. 3. Raise upper handle ...

Page 12 - SNOW CHUTE ASSEMBLY; NOTE: DO NOT overtighten carriage bolts.; SHIFTER LEVER KNOB ASSEMBLY; shifter knob; CHECK THE TIRES; Check the fasteners. Make sure all fasteners are

ASSEMBLY 12 MTF − 051056L SNOW CHUTE ASSEMBLY 1. Position the snow chute to the INSIDE of the snow chute flange. Align the three holes in the snow chute with holes in snow chute flange. (See Figure 8) 2. Place three 5/16 − 18 carriage bolts from inside of chute as shown in Figure 8. (hardware is fou...

Page 13 - OPERATION; ENGINE AND SNOWTHROWER CONTROLS

OPERATION 13 MTF − 051056L READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOWTHROWER. Compare the illustrations with your SNOWTHROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Figure 10 Auger Drive Clutch L...

Page 14 - SNOWTHROWER OPERATION

OPERATION 14 MTF − 051056L The operation of any snowthrower can result in foreign objects being thrown into the eyes,which can result in severe eye damage. Always wear safety glasses or eye shields before beginning snowthrower Operation. We recommend standard safety glasses or Wide Vision Safety Mas...

Page 15 - TO THROW SNOW

OPERATION 15 MTF − 051056L TO THROW SNOW 1. Push down the auger driver lever ( right hand ). See Figure 11. 2. To stop throwing snowl, release the auger drive lever. NOTE: When clearing wet, heavy snow, it is recommended that the ground speed of the unit be reduced, maintain full throttle and do not...

Page 16 - HOW TO SET THE DRIFT CUTTERS; wingnuts; drift cutters

OPERATION 16 MTF--051056L HOW TO SET THE DRIFT CUTTERS (OPTIONAL ACCESSORY ON SOME MODELS) Drift cutters are used to cut a path through snow deeper than the auger housing. 1. Loosen the wingnuts that secure the drift cutters to the auger housing (see Figure 16). 2. Raise the drift cutters to the des...

Page 17 - BEFORE STARTING ENGINE; Check the oil; FILL GAS; BEFORE STOPPING THE ENGINE

OPERATION 17 MTF − 051056L BEFORE STARTING ENGINE Check the oil NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. 1. Make sure the unit is level.Use a high quality detergent oil classified “For Service SG, SH, SJ, SL, or higher”. 2. Remove ...

Page 18 - TO STOP ENGINE; TO START ENGINE

OPERATION 18 MTF − 051056L TO STOP ENGINE CAUTION: To stop the engine, do not move the choke control to CHOKE position. Backfire or engine damage can occur. 1. Move throttle control to SLOW, then to STOP (Figure 18). Figure 18 Throttle Control 2. Pull out safety/ignition key (Figure 19). Figure 19 T...

Page 20 - FROZEN STARTER; How To Use The Clean-Out Tool

OPERATION 20 MTF − 051056L FROZEN STARTER If the starter is frozen and will not turn engine: 1. Pull as much rope out of the starter as possible. 2. Release the starter handle and let it snap back against the starter. Repeat until the engine starts. Warm engines will cause condensation in cold weath...

Page 21 - OPERATING TIPS

OPERATION 21 MTF − 051056L OPERATING TIPS 1. For optimum snow blower efficiency, adjust ground speed, not the throttle. REMEMBER − if the wheels slip, forward speed will be reduced. The engine is designed to deliver optimum performance at full throttle and must be run at this power setting at all ti...

Page 22 - SERVICE RECOMMENDATIONS; PROCEDURE; vice Recommendations; AFTER EACH USE

SERVICE RECOMMENDATIONS 22 MTF − 051056L SERVICE RECOMMENDATIONS PROCEDURE FIRST 2 HOUR BEFORE EACH USE OFTEN EVERY 5 HOURS EVERY 10 HOURS EVERY 25 HOURS BEGINNING EACH SEASON BEFORE STORAGE S N Tighten all screws and nuts √ √ √ O W T H Check Traction Clutch Cable Adjustment (See Cable Adjustment) √...

Page 23 - MAINTENANCE; SNOWTHROWER; LUBRICATION

MAINTENANCE 23 MTF − 051056L Some adjustments will need to be made periodically to properly maintain your snowthrower.All adjustments in the MAINTENANCE section of this manual should be checked at least once each season. SNOWTHROWER Auger and Traction Drive Belts should be adjusted after the first 2...

Page 25 - ENGINE

MAINTENANCE 25 MTF − 051056L ENGINE Check Crankcase Oil Level before starting engine and after each 5 hours of continuous use (see Figure 28). Add proper motor oil as required. NOTE: Overfilling the engine can affect performance. Tighten the oil fill cap securely to prevent leakage. Change Oil every...

Page 26 - TO ADJUST SKID HEIGHT

MAINTENANCE 26 MTF − 051056L WARNING: Always turn unit off, remove igni- tion key and disconnect the spark plug wire be- fore making any repairs or adjustments. AUGER HOUSING HEIGHT ADJUSTMENTTO ADJUST SCRAPER BAR After considerable use, the metal scraper bar will have a definite wear pattern. The s...

Page 27 - BELT ADJUSTMENT; Traction Drive Belt

MAINTENANCE 27 MTF − 051056L BELT ADJUSTMENT Traction Drive Belt The traction drive belt has constant spring pressure and does not require an adjustment. If the traction drive belt is slipping, replace the belt. See “How To Replace The Belts” in the Maintenance section. Auger Drive Belt If your snow...

Page 28 - HOW TO REPLACE THE BELTS

MAINTENANCE 28 MTF − 051056L HOW TO REPLACE THE BELTS The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center.Some steps require the assistance of a second person. How To Remove the Auger Drive Bel...

Page 31 - BELT GUIDE ADJUSTMENT; Auger Drive Cable Adjustment

MAINTENANCE 31 MTF − 051056L BELT GUIDE ADJUSTMENT 1. Remove spark plug wire. 2. Have someone engage auger drive. 3. Measure the distance between the belt guide and belt. The distance should be 1/8 inch (3.175 mm) for guide.See Figure 37. 4. If adjustment is necessary, loosen belt guide mounting bol...

Page 33 - HOW TO ADJUST OR REPLACE

MAINTENANCE 33 MTF − 051056L HOW TO ADJUST OR REPLACE THE FRICTION WHEEL How To Check The Friction Wheel If the snow thrower will not move forward, check the traction drive belt, the traction drive cable or the friction wheel. If the friction wheel is worn or damaged, it must be replaced. See “How T...

Page 36 - HOW TO REMOVE THE SNOW HOOD

MAINTENANCE 36 MTF − 051056L HOW TO REMOVE THE SNOW HOOD To access the spark plug, the snow hood must be removed as follows: 1. Remove the choke control knob (see Figure 51). 2. Remove the ON/OFF key. 3. Remove the four mounting screws. 4. Slowly remove the snow hood (see Figure 52). Make sure that ...

Page 37 - AUGER SHEAR BOLT REPLACEMENT; WARNING: To insure safety and performance; TO ADJUST OR REPLACE THE SPARK PLUG; spark plug

MAINTENANCE 37 MTF − 051056L AUGER SHEAR BOLT REPLACEMENT The augers are secured to the auger shaft with special bolts that are designed to break if an object becomes lodged in the auger housing. Use of a harder bolt will reduce the protection provided by the shear bolt. To replace a broken shear bo...

Page 38 - STORAGE; OFF SEASON STORAGE

STORAGE 38 MTF − 051056L OFF SEASON STORAGE WARNING: Never store the engine, with fuel in the tank, indoors or in a poor ventilated enclo- sure where fuel fumes could reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer, etc. Handle gasoline carefully. It is highly ...

Page 39 - TROUBLE SHOOTING CHART; PROBLEM

TROUBLE SHOOTING CHART 39 MTF − 051056L PROBLEM LOOK FOR REMEDY Difficult starting Defective spark plug. Replace defective spark plug. Engine runs erratically Blocked fuel line. Clean fuel line. Empty gas tank. Check fuel supply, Stale gasoline. Add fresh gasoline with fuel stabilizer. Water or dirt...

Page 40 - NOTES

Page 42 - REPLACEMENT PARTS

REPLACEMENT PARTS 42 MTF − 051056L WE RECOMMEND JOHN DEERE/FRONTIER quality parts and lubricants available at your John Deere/Frontier dealer. PART NUMBERS MAY CHANGE. When you order replacement parts, use the part numbers listed below and on the fol- lowing pages. If a part number changes, your Joh...

Page 43 - Description

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 43 MTF − 051056L ENGINE Á ÁÁ 25 − 1 2 3 25 − 4 25 − 2 25 − 3 5 4 20 22 24 10 6 7 8 11 Ref.Drive Page Ref. Auger Housing Page 9 25 − 2 16 17 18 14 13 15 12 1 27 28 26 Key No. Part No. Description Key No. Part No. Description 1 MT6219 CORD, STARTER 2 − − ...

Page 44 - FRAME

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 44 MTF − 051056L FRAME 162 167 167 162 91 91 122 90 168 103 106 105 108 Ref. Engine Page 110 148 149 107 Ref. Drive Page Ref. Auger Housing Page 111 169 160 123 123

Page 46 - DRIVE

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 46 MTF − 051056L DRIVE Ref. Wheel Page 229 200 223 225 226 227 234 230 221 Ref. Wheel Page Ref. Shift Yoke Page 206 201 203 204 232 234 229 220 220 218 218 207 215 215 238 238 210 212 213 213 217 213 203 204 236 Ref. Frame Page Ref. Wheel Page Ref. Whee...

Page 48 - AUGER HOUSING

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 48 MTF − 051056L AUGER HOUSING 550 551 552 553 554 500 527 481 480 485 499 482 490 491 493 527 522 522 523 521 525 526 525 526 523 524 524 520 510 514 Ref. Gear Case Page 540 541 544 511

Page 50 - DISCHARGE CHUTE

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 50 MTF − 051056L DISCHARGE CHUTE 598 597 596 583 584 599 582 600 602 603 610 601 606 607 607 611 609 600 588 604 592 593 594 595 Ref. Auger Housing Page 600 Pop Rivets

Page 52 - HANDLE

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 52 MTF − 051056L HANDLE 731 734 739 729 766 734 729 739 721 720 735 733 741 740 765 765 725 725 756 724 725 724 728 727 726 727 726 755 750 757 744 751 762 760 745 759 763 Ref. Engine Page 743 766 730 745

Page 54 - SHIFT YOKE

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 54 MTF − 051056L SHIFT YOKE 796 790 792 801 791 800 814 802 812 813 793 Key No. Part No. Description 790 MT581631E701 ROD, SHIFT 791 MT302628 SCREW, 1/4 − 20X.75 792 MT73826 NUT, 1/4 − 20 793 MT318486 NUT, JAM 796 MT304438 KNOB 800 MT760564 LEVER, SPRIN...

Page 55 - CHUTE ROD

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 55 MTF − 051056L CHUTE ROD 856 855 854 855 861 860 863 864 864 867 Ref. Handle Assy 870 852 − 5 852 − 11 852 − 9 852 − 8 852 − 3 868 852 − 13 852 − 10 852 − 1 852 − 2 852 − 6 869 Ref. Auger Housing Assy 852 − 7 852 − 4 Key No. Part No. Description Key N...

Page 56 - CONTROL PANEL

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 56 MTF − 051056L CONTROL PANEL 770 771 771 772 773 772 772 Key No. Part No. Description 770 MT1501203E511 PANEL 771 MT002x99 BOLT, CARRIAGE 772 MT71067 WASHER 773 MT15x145 NUT

Page 57 - WHEELS

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 57 MTF − 051056L WHEELS 679 678 673 675 678 671 655 650 654 652 653 655 671 673 680 676 677 Ref. Drive Page Key No. Part No. Description 650 MT1501562 SHAFT, AXLE 652 MT1501089 SPRKT & HUB 653 MT01x193 SCREW, 1/4 − 20 x 1.75 654 MT15x145 NUT, 1/4 − ...

Page 58 - GEAR CASE

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 58 MTF − 051056L GEAR CASE 340 341 327 326 324 325 324 323 322 301 306 304 310 311 312 320 313 321 303 303 300 310 311 312 316 315 314 304 Key No. Part No. Description 300 MT10577 CASE, GEAR, RH 301 MT10576 CASE, GEAR, LH 303 MT710025 SCREW,1/4 − 20X.75...

Page 59 - DECALS

FRONTIER MODEL ST0726 FACTORY MODEL 626750x16C 59 MTF − 051056L DECALS 1 2 3 4 5 6 7 9 10 11 12 Key No. Part No. Description 1 MT48x5289 DECAL, HAND CONTROL 2 MT7390 DECAL, V − BELTS 3 MT7859 DECAL, OVER ADJUSTMENT 4 MT48x5967 DECAL, ROTATING AUGER 5 MT48x5578 DECAL, THROWN OBJECTS 6 MT48x5965 DECAL...