John Deere 06621213-16 - Manuals

Page 2 - PECO; WARRANTY; PECO Limited Warranty for New Products

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 2 PECO WARRANTY PECO Limited Warranty for New Products A. WHAT IS WARRANTED? PECO extends the following w a r r a n t i e s t o t h e o r i g i n a l purchaser of each new PECO consumer product subject to the following limitations. 1. PRODUCT WARRANT...

Page 3 - SAFETY

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 3 PECO SAFETY 7. Always stop Vac engine when emptying the container. 8. Stop tractor and vac engines and remove spark plug wire before removing or replacing hose, boot, blower cone or performing any maintenance. 9. Mow up and down the face of slopes ...

Page 4 - PARTS LIST

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 4 PECO PARTS LIST REF. NO. PART NO. DESCRIPTION 01 E1039 BOOT (48” DECK) 1 E1113 BOOT (54” DECK) 1 02 J6006 7”-8” HOSE CLAMPS 2 03 ****** 8” x 32” LOWER HOSE 1 04 E6009 8” BLOWER CONE 1 05 A602 5.5HP/BLOWER/BLADE ASSEMBLY 1 OR A638 6HP/BLOWER/BLADE A...

Page 5 - PARTS DIAGRAM

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 5 PECO PARTS DIAGRAM 01 02 03 04 05 06 07 08 12 10 14 09 11 13 15 16

Page 6 - ASSEMBLY

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 6 PECO ASSEMBLY STEP 1: Place the left main frame side leg (A) onto the rear sides of the mower. Secure the left main frame side leg (A) to the rear of the mower using the mower’s preexisting bolts (B). After the left main frame side leg is secure fo...

Page 7 - A B

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 7 PECO ASSEMBLY STEP 4: On the right end of the outer motor mount tube (A) slide the motor mount arm assembly (B) in. Secure using (1) detent pin (PN#J0248). Next place the engine (C) onto the motor mount arm assembly (A). Secure the engine (C) to th...

Page 8 - IMPELLER BLADE REPLACEMENT

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 8 PECO ASSEMBLY STEP 7: The ears of the cone (A) should ﬁt underneath the two threaded bosses on the blowerface (B). Secure with (2) 5/16”-18 x 2” hex bolts (PN#K1159). Use the diagram to the right for more detail. IMPELLER BLADE REPLACEMENT TO REMOV...

Page 9 - TIGHTEN THE HOSE CLAMPS BEFORE EACH USE!

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 9 PECO ASSEMBLY STEP 8: STEP 9: TIGHTEN THE HOSE CLAMPS BEFORE EACH USE! Place the hose clamps over each end of the 6” hose (A). Attach one end of the hose onto the blower hous- i ing (B). Attach the free end of the hose over the inlet (C). Tighten t...

Page 10 - MAINTENANCE; Service; Emptying The Lawn Vac

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 10 PECO MAINTENANCE PECO Lawn Vac Owners should record the name and telephone number of their Service Cen- ter Your Service Center will be happy to supply replacement parts, and accessories as well as perform necessary service or repairs to your lawn...

Page 11 - TROUBLE SHOOTING; Diagnostic Procedures

MODEL 06621213 - 16 JOHN DEERE 717 & 727 PECO 11 PECO TROUBLE SHOOTING Diagnostic Procedures Trouble shooting procedures are provided in the chart below. To use these procedures, ﬁrst locate the problem below that best describes the trouble you have encountered. Check the possible causes in the ...