Jet PDS-12CS - Manuals - manualsarea.com

Page 3 - WARNING

3 WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. This disc sander is intended to be used with wood and wood products only. Use of this disc sander and a dust collector with metal products is a ...

Page 4 - SAND with the grain of the wood.

4 • ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. • REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. • USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by POW ERMATIC may cause hazard...

Page 5 - Grounding Instructions

5 Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the ev ent of a malfunction or breakdown, grounding prov ides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an ...

Page 6 - Disconnect the machine from the power source.

6 230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This POW ERMATIC sander is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these fou...

Page 7 - Specifications PDS-12CS; Down; Table of Contents

7 Specifications PDS-12CS Stock Number............................................................................................................................ 1791201K Disc Diameter .....................................................................................................................

Page 8 - Contents of the Shipping Carton; Read and understand the entire contents of; Unpacking

8 Contents of the Shipping Carton PDS-12CS 12” Disc Sander 1. Sander 1. Sanding Disc 1. Table 1. Miter Gauge 1. Miter Gauge Fence 1. Owner's Manual 1. W arranty Card Hardware Kit 4. Hex Head Bolt M10x35 4. Flat W asher M10 4. Lock W ashers M10 2. Hex Nut M6 4. Pan Head Flange Screw M6x12 1. Center P...

Page 9 - Stand Assembly; hole pattern in the sander.; Sander Assembly; on top of the split pins and threaded shaft.; Avoid kickback by sanding in accordance

9 Stand Assembly 1. W ith the help of another person lift the sander (A, Fig. 1) onto the stand (B, Fig. 1). Feed the belt (C, Fig. 1) through the cut out in the top of the stand. 2. Match the hole pattern in the stand with the hole pattern in the sander. 3. Bolt the sander to the stand with four M1...

Page 11 - All electrical connections must be done by

11 Sanding Disc Replacement 1. Disconnect machine from the power source. 2. Remov e the knobs (A, Fig. 7), washers (B, Fig. 7), and trunnion holders (C, Fig. 7) followed by the table assembly (D, Fig. 7). 3. Remov e old sanding disc by striping from wheel. Use a cleaner and putty knife to remov e th...

Page 12 - CAUTION; Optional Accessories

12 Emptying the Collector Bag CAUTION Wearing a particle mask/respirator for protection against fine dust particles during cleaning is highly recommended. During first use and after cleaning, the bag may allow some dust to escape. This is normal and will stop after a short period of time. Clean the ...

Page 13 - Base Assembly Breakdown

Page 14 - Index Part

14 Parts List for the PDS-12CS Base Assembly Index Part No. No. Description Size Qty 1 .......... 612083 ......................... Closed Stand ......................................... ............................................... 1 2 .......... 612097 ......................... Door w/Latch Assem...

Page 15 - Sander Assembly Breakdown

Page 16 - Description

16 Parts List for PDS-12CS Sander Assembly Index Part No. No. Description Size Qty 1 .......... 612111 ......................... Base ...................................................... ............................................... 1 2 .......... TS-1505051 ................. Socket Head Cap Scr...

Page 18 - Wiring Diagram