Jet JDS-12B - Manuals - manualsarea.com

Page 3 - WARNING

3 WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. This disc sander is intended to be used with wood and wood products only. Use of this disc sander and a dust collector with metal products is a ...

Page 4 - SAND with the grain of the wood.

4 • ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. • REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. • USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or ris...

Page 5 - Grounding Instructions

5 Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the ev ent of a malfunction or breakdown, grounding prov ides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an ...

Page 6 - Disconnect the machine from the power source.

6 230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This JET sander is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor ...

Page 7 - Specifications JDS-12B; Down; Table of Contents

7 Specifications JDS-12B Stock Number................................................................................................................................ 708433 Disc Diameter ....................................................................................................................

Page 8 - Contents of the Shipping Carton; Hardware Kit; Read and understand the entire contents of; Unpacking

8 Contents of the Shipping Carton JDS-12B Benchtop Sander 1. Sander 1. Sanding Disc 1. Table 1. Miter Gauge 1. Inlet 1. Inlet Gasket 1. Owner's Manual 1. W arranty Card Hardware Kit 4. Hex Head Bolt M10x40 8. Flat W asher M10 4. Lock W ashers M10 4. Hex Nut M10 4. Hex Head Bolt M6x16 1. Center Point...

Page 9 - Sander Assembly; on top of the split pins and threaded shaft.; Warning; Avoid kickback by sanding in accordance

9 Stand Assembly (optional accessory) 1. Match the hole patterns in the stand legs with the hole patterns in the stand supports. Mount the legs to the outside of the supports using sixteen M8x16 carriage bolts and sixteen M8 flange lock nuts, figure 1. Do not tighten until the stand has been assembl...

Page 11 - All electrical connections must be done by

11 Center Point The center point (A, Fig. 7) prov ided with the sander can be used for sanding circles. Slide the center point into the miter slot that is perpendicular to the sanding disc. The radius of the desired circle should be the distance from the center point to the sanding disc. Lock the ce...

Page 12 - Cleaning the Filter; CAUTION; Optional Accessories

12 Canister Filter (optional accessory) 1. Remov e the inlet port that came with the sander. 2. Mount the plastic elbow (A, Fig. 9) to the sander using the same hardware (B, Fig. 9) from the inlet port. 3. Connect the filter (C, Fig. 9) to the elbow and turn counter-clockwise so that it locks in pla...

Page 13 - Sander will not start

13 Troubleshooting Trouble Possible Cause Solution Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 1. Check all plug connections 2. Replace fuse or reset circuit breaker 3. Replace cord Sanding disc does not come up to speed 1. Ex...

Page 14 - Disc Sander Breakdown

Page 15 - Description

15 Parts List For The JDS-12B Benchtop Disc Sander Disc Sander Index Part No. No. Description Size Qty 1 .......... 612131 ......................... Guard Base ........................................... ............................................... 1 2 .......... MH612001 ................... Moto...

Page 17 - Open Stand Breakdown (optional accessory); Index Part

17 Open Stand Breakdown (optional accessory) JDS-12B Stand Assembly (optional accessory) Index Part No. No. Description Size Qty. 1 .......... 612141 ............................. Stand Leg ...................................................... ................................... 4 2 .......... 6121...

Page 18 - Wiring Diagram