Jet JDP-17FSE - Manuals - manualsarea.com

Page 3 - WARNING

3 WARNING Wear eye protection. Always keep guards in place and in proper operating condition. Do not operate the machine without the guards for any reason. Support workpiece adequately at all times during operation; maintain control of work at all times. This drill press is designed and intended for...

Page 5 - Grounding Instructions

5 Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the ev ent of a malfunction or breakdown, grounding prov ides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an ...

Page 6 - Disconnect the machine from the power source.

6 230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This JET drill press is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four m...

Page 7 - On-Off Switch Padlock

7 On-Off Switch Padlock Model No. BP-1, Stock No. 709736 To safeguard your machine from unauthorized operation and to av oid accidental starting by young children, the use of a padlock is highly recommended. JET model BP-1 is av ailable from your local authorized JET distributor or by calling JET Eq...

Page 9 - Contents of the Shipping Container; Assembly; Tools Supplied for Assembly; W rench; Read and understand all assembly

9 Contents of the Shipping Container 1. Head Assembly 1. Table 1. Column and Bracket Assembly 1. Base 1. Owner’s Manual 1. W arranty Registration Card 1. Chuck and Chuck Key 3. Downfeed Handle 1. Table Bracket Lock Handle 1. Table Bracket Raising Handle 4. M10 x 40 Hex Cap Bolts 1. Arbor 1. Drift Ke...

Page 10 - W ith a 17mm wrench attach the column

10 Assembly 1. Place the base (A, Fig. 1) on a lev el floor. 2. W ith a 17mm wrench attach the column assembly (B, Fig. 1) to the base (A, Fig. 1) with four M10 x 40 hex cap bolts (C, Fig. 1). Tighten firmly. 3. Thread lock handle (D, Fig. 2) into the table bracket (E, Fig. 2). 4. Loosen the set scr...

Page 11 - Removing the Chuck and Arbor; and lower quill using the down feed handle.

11 9. W ith the aid of a second person, carefully lift the head onto the column top. Caution: The head assembly is heavy! Use care when lifting onto the column! 10. Rotate head assembly until sides of the belt cov er are parallel with the sides of the base. 11. Tighten two set screws (A, Fig. 4) wit...

Page 12 - each side of the head assembly.

12 Adjusting the Depth Stop To drill multiple holes at the same preset depth, use the depth stop: 1. Lower the bit until it touches the workpiece. 2. Loosen lock knob (A, Fig. 7) and rotate housing (B, Fig. 7) until the pointer lines up with the depth you want to drill, indicated by the scale. 3. Ti...

Page 13 - Speed & Pulley Chart

Page 14 - Remove the alignment pin first and then; table to the desired angle.

14 Return Spring Adjustment The return spring is adjusted at the factory and should not need further adjustment. If adjustment is deemed necessary: 1. Unplug the machine from the power source. 2. Loosen two jam nuts (A, Fig. 10). Do not remove. 3. Firmly hold the coil spring cov er (B, Fig. 10). 4. ...

Page 15 - Basic Operation; If the work piece is not large enough to; Lubrication

15 Basic Operation • Always use a back-up piece of scrap wood to cov er the table. This protects both the table and the drill bit. • Place material to be drilled in such as way as to come into contact with the left side of the column. This prev ents the material from spinning. WARNING! If the work p...

Page 16 - Troubleshooting; Trouble Probable

16 Troubleshooting Trouble Probable Cause Remedy Drill press will not start. 1. Drill press unplugged from wall, or motor. 2. Fuse blown, or circuit breaker tripped. 3. Cord damaged. 4. Starting capacitor bad. 1. Check all plug connections. 2. Replace fuse, or reset circuit breaker. 3. Replace cord....

Page 17 - Parts Breakdown for JDP-17FSE

Page 18 - Parts List for JET JDP-17FSE Drill Press; Description

18 Parts List for JET JDP-17FSE Drill Press Index Part No No. Description Size Qty 1 .......... 10800101 ..................... Base .................................................................. ................................... 1 2 .......... 12909001A1................. Column Holder Assy (in...