JENSEN VM9114 - Manuals - manualsarea.com

Page 3 - CONTENTS

iii VM9114 CONTENTS Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen VM9114 Mobile Multimedia Receiver for maximum...

Page 5 - FEATURES; DVD

1 VM9114 FEATURES Congratulations on your purchase of the Jensen VM9114 Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9114 installed by a reputable installation shop. DVD • Fast Forward/Reverse - 2X, ...

Page 7 - CONTROLS AND INDICATORS; BAND; Press and hold

3 VM9114 CONTROLS AND INDICATORS 1. CLOSE/OPEN Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. PIC/BAND Press to adjust the Brightness and Contrast (see “Image/Display Settings” on page 6). With the monitor closed, pr...

Page 9 - USING THE TFT MONITOR; Open/Close TFT Monitor; Open TFT Monitor; Close TFT Monitor; OPEN; TFT Monitor Auto Open; OPEN; Monitor Tilt Angle Adjustment

5 VM9114 USING THE TFT MONITOR Open/Close TFT Monitor Open TFT Monitor Press the OPEN button (1) on the front panel to activate the mechanism that moves the display panel into the viewing position. Close TFT Monitor Press the OPEN button (1) on the front panel to load the display panel back into the...

Page 10 - Aspect Ratio; WIDE; Image/Display Settings; Video Output Modes; PIC; Playing Source

6 VM9114 Aspect Ratio Press and hold the WIDE button (4) on the monitor to adjust the aspect ratio as follows: Image/Display Settings Video Output Modes Table 1 shows the video output mode for each playing source. *CVBS – Composite Video Baseband Signal Picture Adjustment To adjust monitor display s...

Page 11 - Press the; Parking Brake Inhibit

7 VM9114 3. Press the PIC button on the monitor (2) 1-3 times to exit the picture adjustment menu. Parking Brake Inhibit When the pink "Parking" wire is connected to the vehicle Parking Brake circuit, the front TFT monitor will display video when the Parking Brake is engaged. (When the pink ...

Page 12 - OPERATING INSTRUCTIONS; Audible Beep Confirmation; MUTE; Playing Source Selection; Source Menu; SRC; SOURCE MENU

8 VM9114 OPERATING INSTRUCTIONS Power On / Off Press the /SRC button (10) on the unit to turn the unit on. You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment. Au...

Page 13 - External Devices; Volume Adjustment; Volume Increase/Decrease; Audio Control Menu

9 VM9114 External Devices External peripheral devices, including a game console, camcorder, navigation unit, iPod, Zune, etc. can be connected to this unit via RCA output using an A/V Media Adapter Cable (not included). Connect the external device to the A/V Media Adapter Cable and then plug the cab...

Page 14 - Touch the; EQ; button on the left side of the screen to display the audio menu.; System Reset; Table 3: Audio Adjustments; Audio Function

10 VM9114 Touch the EQ button on the left side of the screen to display the audio menu. Use the touch screen + / - buttons to adjust the settings for an audio feature. NOTE: The EQ mode will automatically change to “USER” when individual audio functions are adjusted. The Audio menu will automaticall...

Page 15 - Accessing Menu Items; SETUP MENU

11 VM9114 SETUP MENU To access system settings, touch the button on the screen to enter the “SETUP” menu. The “GENERAL” sub-menu appears highlighted in blue. Accessing Menu Items Touch the sub-menu name to select a sub-menu (Language, Audio, RDS, etc.). The features available for adjustment under th...

Page 16 - Setting

12 VM9114 General Sub-menu Features Language Sub-menu Features If a DVD supports more than 1 Subtitle or Audio language, all the languages are available for selection during playback. If the selected language is not Setting Options Function Clock Mode 12Hr Clock displays 12 hour time using AM and PM...

Page 18 - Hardware Sub-menu Features

14 VM9114 To reset the password, access the “RATING” menu and enter the current password. Once the correct password is entered, you can access the “Password” field and enter a new one. NOTE: Record the password and keep it in a safe place for future reference. The rating for each disc is marked on t...

Page 19 - Demo Sub-Menu Features; Exiting the System Setup Menu; To exit setup mode and resume normal playback, touch the; BACK; button on

15 VM9114 P.VOL Sub-menu Features TS Cal (Screen Calibration) To access the “Screen Calibration” function from the SETUP menu, select the “TS CAL” option. After entering calibration mode, a crosshair appears in a corner quadrant of the screen. To begin calibration, touch and hold the crosshair for o...

Page 20 - TUNER OPERATION; Tuner TFT Display

16 VM9114 TUNER OPERATION Tuner TFT Display 1. Current radio band indicator 2. Radio frequency indicator 3. Clock 4. Stereo broadcasting indicator 5. Strong Local signal broadcasting indicator 6. Preset radio stations: Touch to recall preset stations 7. Information about the current function 8. EQ :...

Page 21 - Switching to Radio Tuner Source; NOTE: The BAND button on the unit only works when the TFT is closed.; Seek Tuning; Clear

17 VM9114 Switching to Radio Tuner Source • Touch the top left corner of the screen to view the SOURCE MENU. Touch “Radio”. • Press the SRC button (10) on the front panel or remote control (8) to switch to the AM/FM or RADIO source. Selecting FM/AM Band Touch the BAND button (15) on the screen to ch...

Page 22 - Using Preset Stations; Storing a Station; MEM; Recalling a Station; AS

18 VM9114 Using Preset Stations Six numbered preset buttons store and recall stations for each band. All six stored stations (P1-P6) for the current band appear on the screen. Storing a Station 1. Select a band (if needed), then select a station. 2. Touch the on-screen MEM button (18) to open the pr...

Page 24 - DVD/VCD VIDEO OPERATION; Opening/Closing the TFT Video Screen; Opening the TFT Screen; Closing the TFT Screen; Inserting a Disc; press and hold; Accessing DVD Mode

20 VM9114 DVD/VCD VIDEO OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen display a parking brake notice. Rear video screens, if applicable, will ...

Page 25 - Controlling Playback

21 VM9114 Controlling Playback To access the on-screen controls, touch the bottom 1/3 of the screen while a DVD is playing. Touch the 1/2 button to view a second page of controls Stopping Playback Touch the stop button ( ) on the screen to stop DVD play. Pausing Playback Touch the play/pause button ...

Page 26 - NOTE: For VCD play, the repeat function is not available if PBC is on.; Accessing the DVD Menu; Moving Through Chapters

22 VM9114 • VCD (PBC Off): Repeat Single, Repeat Off NOTE: For VCD play, the repeat function is not available if PBC is on. Sectional Repeat Function (A-B) Use the A-B function to define a specific area of a disc to repeat. • Touch the A-B button on the second page of DVD on-screen controls to set t...

Page 27 - Viewing an Alternate Picture Angle (DVD Only); Changing Audio Language; AUDIO; Changing Subtitle Language; SUBTITLE; Playback Information; DISP; DVD Playback Information

23 VM9114 Viewing an Alternate Picture Angle (DVD Only) Some DVDs contain scenes that have been shot simultaneously from different angles. For discs recorded with multiple angles, touch the button on the second page of DVD on-screen controls to toggle available angles of the on-screen image. Multi-L...

Page 28 - General Disc Information; Table 4: Disc Properties; Table 5: Disc Symbols; Symbol

24 VM9114 • Chapter 2/16 – Indicates that the second of 16 chapters on the DVD is currently playing. VCD Playback Information • VCD2.0 – Format of current disc. • Time 00:01:30/00:36:10 – Indicates the playback time of the current track. • PBC On/Off – Indicates whether Play Back Control is On or Of...

Page 30 - DVD/CD AUDIO OPERATION; CD Player User Interface

26 VM9114 DVD/CD AUDIO OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and CD operation. Please see the DVD/Disc Video Operation section for information about these topics. The VM9114 will play music or other audio files from the following disc media: • CD-DA • CD-R/RW •...

Page 31 - Stopping Playback; SCAN; Random Play Select; RDM

27 VM9114 11. : Touch to rewind current track 12. : Touch to activate/deactivate Repeat play mode 13. : Touch to activate/deactivate Random mode 14. : Touch to access the direct entry screen 15. : Touch to view the SETUP menu 16. EQ : Touch for quick access to Equalizer level settings 17. Touch to v...

Page 32 - Fast Forward; Direct Track Entry

28 VM9114 Fast Forward Touch the button to fast forward. Keep pressing and releasing the button to increase the rate from “x2” to “x4”, “x8”, and “x20”. Touch the /|| button to resume normal playback. Direct Track Entry To select a track directly, touch the on-screen button to display the direct ent...

Page 33 - Media and File Requirements; MP3 Format Compatibility

29 VM9114 MP3/WMA OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and MP3 operation. Please see the DVD/Disc Video Operation section for information about these topics. Media and File Requirements This player allows you to play back MP3 and WMA files recorded onto CD-R/R...

Page 34 - Inserting a USB Device; Lift the protective cover to reveal the USB slot.

30 VM9114 For example, a medium with the following folder/file hierarchy is subject to Folder Search, File Search or Folder Select, as shown below. The VM9114 player will only recognize three folder levels and does not display folders containing only other folders. In the example above, the unit wil...

Page 35 - MP3 User Interface

31 VM9114 To remove the USB device, press the SRC button (10) or use the SOURCE MENU to switch to another mode, and then remove the USB device from the connector. MP3 User Interface The on-screen indicators and touch key areas for MP3 playback are outlined below. 1. Current track and total number of...

Page 36 - Playing MP3/WMA Files

32 VM9114 11. : Touch to Fast Backward x2, x4, x8, x20 12. DIR - : Touch to view the previous folder 13. DIR + : Touch to view the next folder 14. : Touch to access the direct entry screen 15. : Touch to view the SETUP menu 16. EQ : Touch for quick access to Equalizer level settings 17. Touch to vie...

Page 38 - TROUBLESHOOTING; Table 6: Troubleshooting; Problem

34 VM9114 TROUBLESHOOTING Table 6: Troubleshooting Problem Cause Corrective Action GENERAL Unit will not power on Radio Fuse blown Install new fuse with correct rating Car battery fuse blown Install new fuse with correct rating Illegal operation Press the RESET button located in the bottom right cor...

Page 40 - Do not get water or cleaning fluids on the unit.; Table 7: Error Messages

36 VM9114 Error Messages Care and Maintenance 1. Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A rough cloth and non-neutral detergent (such as alco-hol) may result in scratching or discoloration. 2. Do not get water or cleaning fluids on the unit. 3. If ...

Page 42 - SPECIFICATIONS

38 VM9114 SPECIFICATIONS DVD/CD Player Compatible Disc Media: DVD + R / RW (Single and Dual Layer) and CD-R / RWCompatible Media Formats: CD-DA, MP3, WMA, VCD, SVCD, Xvid, AVI, MPEG 1/2 Signal to Noise Ratio: >95dBADynamic Range: >95dBFrequency Response: 20Hz to 20 kHz, -3dBChannel Separation:...