JENSEN KT2012 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INSTRUCTIONS; CAUTION; SAVE THESE INSTRUCTIONS; AGES 8 and UP

1 IMPORTANT SAFETY INSTRUCTIONS This symbol is to alert you the important operating or servicinginstructions that may appear in your owner’s manual. Alwaysfollow basic safety precautions when using this product to reducethe risk of injury, fire or electric shock. When using your telephone equipment,...

Page 3 - FCC INFORMATION; following information provided by the FCC.

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The telephone company may take changes in its communications facilities,equipment, operations or procedures, where such action is reasonably required andproper in its business. Should any such changes render the customer’s terminalequipment incomp...

Page 4 - BATTERIES CAUTIONARY INSTRUCTIONS; codes for possible special disposal instructions.; INTRODUCTION TO CALLER ID INSTRUCTIONS; Read this manual carefully before using this product.

BATTERIES CAUTIONARY INSTRUCTIONS CAUTION – To Reduce the Risk of Fire or injury to Persons, Read and Followthese instructions. 1. Use only the following type and size of battery: 4 ‘C’ size (UM-2) alkaline batteries.2. Do not dispose of the battery in a fire. The cell may explode. Check with local ...

Page 5 - CONTROLS AND FEATURES; Features; calls that you have received.; LOCATION OF CONTROLS

CONTROLS AND FEATURES Features 1. This product features Caller ID.2. Displays the caller’s name, telephone number, time and date of the last 64 incoming calls that you have received. 3. Large three lines high resolution LCD display.4. Display Total and New Calls received in standby screen.5. Up / Do...

Page 6 - to have the ringer sound when receiving a phone call.

9 HANDSET BOTTOM OF BASE 1.Receiver2.Hook Switch3.TONE/PULSE Switch4.Key Buttons (0-9,*,#)5.MEMO Button6.STORE Button7.Transmitter8.RECEIVER (NORMAL/HIGH) Volume Switch9.REDIAL Button10.FLASH Button11.Battery Compartment12.DC IN Jack13.OFF/LO/HI Ringer Switch14.Handset Jack15.Line In Jack LOCATION O...

Page 7 - SELECT THE LANGUAGE; ] buttons simultaneously for four seconds until; SETUP PROCEDURE; PLACING A CALL; The last 64 incoming calls are saved in the caller ID log.; BASIC OPERATIONS

11 DO NOT CONNECT the line cord to the wall outlet until the caller ID setup hasbeen completed. Set the language, contrast, time and date as follows: Press and hold the [ ] and [ ] buttons simultaneously for four seconds until"ENTER LANGUAGE" appears,followed by "ENG ESP FRA" for 20s...

Page 8 - STORING AND REDIALING NUMBERS IN THE SPEED-DIAL MEMORY; You must lift the handset from the cradle to store numbers in the; TO STORE

14 If you are in a Pulse dialing area youmay still take advantage of touch-toneservices after dialing to respond totouch-tone prompts. To do this, pressthe */TONE button to temporarilychange the dialing mode from Pulse toTone after dialing in the Pulse mode.This will enable Pulse users to accesstouc...

Page 9 - TO CHANGE A STORED NUMBER:; you stored on the small index card in the center of the cradle.; MESSAGE WAITING FUNCTION; ] button to view the most; ERASING THE CALLER ID MEMORY; To erase all calls

15 Verify that the number on the display iscorrect, then press the STORE buttonagain. The Memory indicator (“MEM”)will appear in the display. Press the number “1” button to store thedisplayed number in memory location 1.Repeat steps 1 through 4 to store up tonine additional numbers in memories “2”th...

Page 10 - COPYING CALLER ID INFO TO A MEMORY PRESET; ] button to locate a caller ID

COPYING CALLER ID INFO TO A MEMORY PRESET Press the [ ] or [ ] button to locate a caller ID call to be copied into amemory preset. Press the STORE button twice:“MEM” will be displayed on the display.Press the Key buttons (0-9) to enter thedesired memory location Repeat thesesteps for additional pres...

Page 11 - TROUBLESHOOTING; PROBLEMS; Reset the language by pressing the

19 TROUBLESHOOTING 20 PROBLEMS CHECK No dial tone Is any plug disconnected from all modular phone plugs? Is jack improperly wired? Phone does not work Are all cords connected properly? Phone does not ring Ringer Switch may be set to OFF? Slide switch to ON position. Cannot dial Check the Tone/Pulse ...

Page 12 - CONSUMER INFORMATION; If your home has specially wired alarm equipment connected to the

This equipment complies with Part 68 of the FCC rules and the requirementsadopted by the ACTA On the bottom of this equipment is a label that contains,among other information, a product identifier of US: 2BFMT09BKT2010.If requested, this number must be provided to the telephone company. The applicab...