JennAir JLRP436WP00 - Manuals

Page 2 - RANGE SAFETY; DANGER

2 RANGE SAFETY You can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what canhappen if the instructions are n...

Page 3 - WARNING

3 In the State of Massachusetts, the following installation instructions apply: ■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by the State of Massachusetts. ■ If using a ball valve, it shall be a T-handle type. ■ A fl...

Page 4 - INSTALLATION REQUIREMENTS; Tools Needed

4 Tools & Parts INSTALLATION REQUIREMENTS Tools Needed Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Pipe wrench Adjustable wrench or 5 ⁄ 8 " wrench Z\, " x 4 1 / 4 " flat-blade screwdriver #2 P...

Page 5 - Parts Needed

5 NOTE: Anti-tip bracket must be securely mounted to subfloor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store. See “Install Anti-Tip Bracket” section. ■ Gas pressure regulator ■ Burner grates ■ Burner bases an...

Page 6 - Mobile Home – Additional Installation Requirements; Location Requirements

6 IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. ■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located under the console on the...

Page 7 - Cabinet Dimensions

7 48" (121.9 cm) models A. Island trimB. 27 1 ⁄ 8 " (68.9 cm) depth with control panel (See NOTE) C. 35¾" (90.8 cm) cooktop height when sitting on the wheelsD. 48" (121.9 cm) widthE. Model/serial rating plate location B C E D A NOTE: When installed in a 24" (61.0 cm) base cabinet...

Page 8 - Electrical Shock Hazard; IMPORTANT: The range must be electrically grounded in; Electrical Requirements; Explosion Hazard; Type of Gas; Gas Supply Requirements

8 Electrical Shock Hazard Plug into a grounded 3 prong outlet.Do not remove ground prong.Do not use an adapter.Do not use an extension cord.Failure to follow these instructions can result in death, fire, or electrical shock. WARNING IMPORTANT: The range must be electrically grounded in accordance wi...

Page 9 - Gas Supply Line; Flexible Metal Appliance Connector:; Gas Pressure Regulator

9 Gas Supply Line ■ ■ ■ Provide a gas supply line of ¾" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. With LP gas, piping or tubing size can be ½" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materia...

Page 10 - Excessive Weight Hazard; Unpack the Range; b. Lay kick plate to the side to avoid scratching; INSTALLATION INSTRUCTIONS; NOTE: This support is used only for shipping and is not

10 WARNING Excessive Weight Hazard Use two or more people to move and install range.Failure to do so can result in back or other injury. 1. Remove shipping materials, tape, and film from range. Keep shipping pallet under range. Remove oven racks, grates, and parts package from inside oven. 2. Remove...

Page 11 - Wall Mounting; Install Anti-Tip Bracket

11 A B C A. Centerline B. Centerline of cutout to outside edge of anti-tip bracket C. Back wall to back of range 3. Drill two ¹⁄ 8 " (3.0 mm) holes that correspond to the bracket holes of the determined mounting method. See the following illustrations.Floor Mounting B A A. #12 x 1 5 ⁄ 8 " sc...

Page 12 - Make Gas Connection; Verify Anti-Tip Bracket Location; Complete Connection

12 Make Gas Connection WARNING Explosion Hazard Use a new CSA International approved gas supply line.Install a shut-off valve.Securely tighten all gas connections.If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column. Examples of a qualified ...

Page 13 - Install Burner Bases and Burner Caps

13 Level Range NOTE: Range must be level for satisfactory baking performance.1. Place rack in oven.2. Place level on rack and check levelness of the range, first side to side, then front to back. 3. If range is not level, adjust the leveling rods. Turn leveling rods located behind the kick plate to ...

Page 15 - Reinstall Kick Plate; Complete Installation; Check Operation of Oven Broil Burner

15 A Reinstall Kick Plate 1. Align shoulder screw mounting holes with shoulder screws on range. 2. Push kick plate down against front of range until the top screw holes are aligned with the mounting holes on the front of the range. 3. Reattach screws to the top of the kick plate. A B D C A. Kick pla...