JennAir JED8230ADS - Manuals

Page 2 - INSTALLATION REQUIREMENTS; Tools and Parts; Tools needed; Location Requirements; Product Dimensions

2 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed Parts supplied ■ Vent grille ■ Grease filter ■ Grill cartridge ■ Grease container(s) ■ Hold-down straps (4)...

Page 3 - Cabinet Dimensions

3 45" (114.3 cm) Cooktop * A minimum clearance of 6¹⁄₄ " (15.9 cm) is recommended for removal of the grease containers. Installed dimension for the grease containers is 5 ¹⁄₂ " (14.0 cm). ** A minimum clearance of 2 " (5.1 cm) is recommended between the motor/blower and cabinet for p...

Page 4 - Cutout Dimensions; Venting Requirements; For Best Performance:

4 NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout. ■ Where possible, a 6" (15.2 cm) clearance is recommended for moto...

Page 5 - Venting Methods

5 ■ Make sure there is a minimum of 18" (45.7 cm) of straight vent between the elbows if more than one elbow is used. ■ Elbows too close together can cause excess turbulence that reduces airflow. ■ Do not use a 5" (12.7 cm) elbow in a 6" (15.2 cm) or 3 ¹⁄₄ " x 10" (8.3 x 25.4 cm)...

Page 6 - Vent Piece

6 Concrete Slab Installations - Exhaust Through Window Well Concrete Slab Installations - Exhaust Through Wall Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system. A. Wall capB. 12" (30.5 cm) minim...

Page 7 - Using 2 or more people, place cooktop on floor with front; Remove the four acorn nuts (A) that attach the blower motor; Slowly reach in the blower exhaust scroll opening and; Electrical Requirements; WARNING

7 Example vent system NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance. Determine Range Blower Setting This cooktop is equipped with a dual range blower. It is shipped from the factory in the low range for most installatio...

Page 8 - Before You Make the Electrical Connection:; INSTALLATION INSTRUCTIONS; Prepare Cooktop; Excessive Weight Hazard

8 Make sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances. A copy of the ab...

Page 9 - Rotate Blower - Optional; To rotate blower motor:

9 Rotate Blower - Optional IMPORTANT: The following additional steps must be performed if the product is being installed in peninsula or island cabinetry. The blower exhaust scroll is shipped from the factory set to exhaust straight out the back of the cabinet through an exterior wall. To rotate blo...

Page 10 - Install Cooktop; Make Electrical Connection; Electrical Connection Options; Electrical Shock Hazard

10 Install Cooktop 1. Using 2 or more people, place cooktop right side up into the cutout. NOTE: Make sure that the front edge of the cooktop is parallel to the front edge of the countertop. If repositioning is needed, lift entire cooktop up from the cutout to avoid scratching the countertop. 2. Con...

Page 11 - Complete Installation; If you need Assistance or Service:

11 3-Wire Cable from Home Power Supply to 4-Wire Cable to Cooktop - U.S. only IMPORTANT: Use the 3-wire cable from power supply where local codes permit connecting the frame-ground conductor to the neutral (white) junction box wire. 1. Disconnect power. 2. Remove wiring box cover from the cooktop pl...

Page 12 - Notes