JennAir JDRP536WP03 - Manuals

6 Location Requirements IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. ■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial/rating plate. The model/serial/rating plate is located un...

7 48" (121.9 cm) models NOTE: When installed in a 24" (61.0 cm) base cabinet with 25" (63.5 cm) countertop; front of oven door protrudes 1 7 / 8 " (4.8 cm) beyond 24" (61.0 cm) base cabinet. Cabinet Requirements Cabinet opening dimensions shown are for 25" (64.0 cm) counterto...

8 Electrical Requirements: U.S.A. Only If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes.If codes permit and a separate ground wire is used, it is recommended th...

9 Electrical Requirements: Canada Only If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes.Be sure that the electrical connection and wire size are adequate and in...

10 Gas Supply Line ■ Provide a gas supply line of 3/4" (19 mm) rigid pipe to the cooktop location. A smaller size pipe on longer runs may result in insufficient gas supply. With Propane gas, piping or tubing size can be 1/2" (13 mm) minimum. Usually, Propane gas suppliers determine the size ...

11 INSTALLATION INSTRUCTIONS Unpack the Range 1. Remove shipping materials, tape, and film from range. Keep shipping pallet under range. Remove oven racks, grates, and parts package from inside oven. 2. Remove kick plate.Your range will either have the kick plate already installed (follow Option 1) ...

12 Install Optional Backguard All ranges may require a backguard. See “Cabinet Dimensions” in the “Location Requirements” section. See the “Tools and Parts” section for information on ordering.Remove island trim and attach backguard using six screws. Insert three from the front and three from the ba...

13 Electrical Connection: U.S.A. Only 30" (76.2 cm) and 36" (91.4 cm) Models 48" (121.9 cm) Models 1. Disconnect power. 2. Remove the terminal block cover screws and disengage mounting tabs to remove terminal block cover from back of range. 3. Add power supply cord strain relief. ■ Assem...

14 4‑Wire Connection: Power Supply Cord Use this method for: ■ New branch-circuit installations (1996 NEC) ■ Mobile homes ■ Recreational vehicles ■ In an area where local codes prohibit grounding through the neutral 1. Remove the ground-link screw from the range frame. Save the ground-link screw. Be...

15 3. Attach one adapter to the gas pressure regulator and the other adapter to the gas shut-off valve. Tighten both adapters, being certain not to move or turn the gas pressure regulator. 4. Use a 15/16" (24 mm) combination wrench and an adjustable wrench to attach the flexible gas supply to th...

16 Electronic Ignition System Install Burner Bases and Burner Caps Install the burner base, making sure the igniter electrode is properly aligned with the base. Place burner caps on top of burner bases. If burner caps are not properly positioned, surface burners will not light. Ultra Power™ Dual‑Fla...

17 7. Put a control knob onto the valve stem of the burner you want to adjust. 8. Turn the control knob to LO and, using a butane extension lighter, light the burner. 9. Remove the control knob. 10. Use a 1/8" x 4 1 / 4 " (3 mm x 100 mm) flat-blade screwdriver to adjust the flame height. Tig...

18 Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. For oven use and cleaning, read the Use and Care Guide. ...

19 To Convert Gas Pressure Regulator 1. Remove the access cap by using a wrench, turning the access cap counterclockwise. 2. Remove spring retainer from the cap by pushing against the flat side of the spring retainer. Look at the spring retainer to locate the “NAT” or “LP” position. Turn over the sp...

20 6. Place Natural gas orifice in plastic parts bag for future use, and keep with package containing literature. NOTE: There may be extra orifices in your kit. 7. Replace the burner base. 8. Replace burner cap. 9. Repeat steps 2 through 8 for the remaining burners. Complete Installation 1. Refer to...

21 Convert Surface Burners 1. If the burner grates are installed, remove them. 2. Remove burner cap. 3. Remove the burner base. A B Large Dual Burner A. Burner capB. Burner base A B C Medium Burner A. Burner capB. Burner baseC. Choke (for use with medium burner, Propane gas only) A B Small Burner A....