JBL SUB12 - Manuals - manualsarea.com

Page 2 - 20V ELECTRICAL PARTS LIST .....................................11; BASIC SPECIFICATIONS; Amplifier Power output:; 50W Continuous RMS power; Amplifier Peak Dynamic Power

- CONTENTS - BASIC SPECIFICATIONS……………….….….….….…………….1 PACKAGING…………………………….………………………......2 DETAILED SPECIFICATIONS ……..…………….……………..3 CONNECTIONS..……………………………………………………5 OPERATION ………….……………………………..…………….7 TEST SET-UP AND PROCEDURE……………………………….8 EXPLODED VIEW /PARTS LIST…………………………………..9 BLOCK DIAG...

Page 4 - 50W Powered Sub/ Plate Amp

VENUE SUB12 150W Powered Sub/ Plate Amp LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation EU 230vac/50-60Hz Yes 207-264 230 Vrms Normal operation, MOMS required Parameter Specification Unit QA Test Limits Conditions Notes Amp Section Type (Class AB, ...

Page 6 - Rear Panel; ONTROLS AND; Subwoofer-Level Control; LEVEL; POWER; JBL Venue

Rear Panel C ONTROLS AND C ONNECTIONS ¡ Subwoofer-Level Control ™ LFE/Normal Selector £ Phase Switch ¢ Crossover Adjustment ∞ Line-Level/LFE Input § High (Speaker)-Level Inputs ¶ Power Switch • Status LED CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CROSSOVERFREQUENCY LEVEL LINE LEVEL IN PHASE Min Max...

Page 7 - SYSTEM CONNECTIONS; If you have a Dolby; Front Speaker Output; This figure shows how to connect bare wires to the terminals.

SYSTEM CONNECTIONS If you have a Dolby ® Digital or DTS ® receiver/processor with a low-frequency-effects (LFE) or subwoofer output: If your receiver/processor does not have subwoofer outputsfor the left and right channels or an LFE output, connectspeaker wire from your receiver/amplifier to your sp...

Page 8 - OPERATION

Power On Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on theback of the receiver. Initially set the Subwoofer-Level Control ¡ to the “min” position. Turn on your sub by pressing the Power Switch ¶ on the rear panel. Turn on your entire audio system and start a CD or movie...

Page 9 - SUB12 Test Set Up and Procedure; Sweep Function

SUB12 Test Set Up and Procedure Equipment needed: • Function/signal generator/sweep generator • Integrated Amplifier • Multimeter • Speaker cables General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect line level (RCA) cables to the Subwoofer Line Level Input jacks L/R o...

Page 12 - Resistors

SUB12 120V Electrical parts list Part number Description Qty Reference Designator MAIN/PREAMP PCB Resistors 021-220202-120ZS MOF resistor 22R 2W(S) J MB TY 1 R10 021-120403-020ZS GS MOF Resistor 1K2 3WS J 8x20 Kink 1 R9 021-120405-020ZS GS MOF Resistor 1K2 5WS J 8x25 Kink 1 R6 024-000098-120ZS GS SM...

Page 13 - Semiconductors

Part number Description Qty Reference Designator 024-680498-120ZS GS SMD resistor 6K8 1/8W J 0805 T 1 R91 026-200595-269ZS GS VR 20k x 2 CROSSOVER PN:RD163121R03D-2 1 VR2 026-500495-005ZS GS VR 5K LEVEL PN:RD163111R22B-5 1 VR1 Semiconductors 054-414803-100ZS GS SMD DIODE PN:LL4148 MINI-ME 15 D3,4,10...

Page 14 - Miscellaneous; MISCELLANEOUS/MECHANICAL

Part number Description Qty Reference Designator 034-220525-301ZS GS Electrolytic cap. 22uF/25V M (R)5x1 2 C50,53 034-330525-300ZR GR Electro. Cap. 33uF/25V M (R)051 1 C1 034-330615-300ZS GS Electrolytic cap. 330uF/16V M (R)08 1 C78 034-470515-307ZR GS Electrolytic cap. LOW ES 47uF/16V M (R)05 1 C65...

Page 18 - Venue