JBL S4S - Manuals - manualsarea.com

Page 2 - NCLUDED; A complete S4S loudspeaker system includes the S4S; HANK; JBL

I NCLUDED S4S (1) Loudspeaker with grille (6) Small grille spacers (for applications requiring one layer of wallboard) (6) Large grille spacers (for applications requiring two layers of wallboard) (6) Grille cups IMPORTANT NOTE: A complete S4S loudspeaker system includes the S4S in-wall subwoofer an...

Page 3 - A single S4S subwoofer system meets THX

3 S PEAKER P LACEMENT Low-frequency sounds are normally omnidirectional, meaning the listener can’t tell where they are generated from.However, frequencies between 75Hz and 150Hz can be localized, especially at higher volume levels. Positioning yoursubwoofer as recommended will provide the most natu...

Page 4 - Connection Tips; Wire Length

4 S PEAKER C ONNECTIONS Connection Tips Speakers and electronics have corresponding (+) and (–) terminals. Mostmanufacturers of speakers and electronics, including JBL, use red to denote the (+)terminal and black for the (–) terminal. It is important to connect both speakers iden-tically: (+) on the...

Page 5 - Using Two S4S Loudspeakers

5 S PEAKER C ONNECTIONS – + Amplifier Top of S4SBB Receiver/Processor Speaker-Level Outputs Subwoofer Out Line-Level Input Using One S4S Loudspeaker in Mono Mode – + Amplifier Left S4S Back Box Right S4S Back Box Receiver/Processor Speaker-Level Outputs Subwoofer or Main Amp Out Line-Level Inputs – ...

Page 6 - NSTALLATION; Included with the S4SBB:

6 I NSTALLATION A complete S4S loudspeaker system includes the S4S in-wall subwoofer and the S4SBB back box. These compo-nents are packaged separately. NOTE: The THX Ultra2 standard requires that the S4S baffle be mounted vertically. Installation requires access to the space between the wall studs. ...

Page 7 - GRILLE SPACER

Installation: 1. Place the Styrofoam ™ blocks on the bottom plate of the stud bay. The S4SBB back box will rest on top ofthe blocks. 2. Install the two centering bars as shown in Detail A on page 6. The centering bars are for setting the depth ofthe enclosure. They also help locate the horizontal po...

Page 8 - CUTOUT; BAFFLE

8 D IMENSION D RAWINGS 2.00 5.13 CABINET 63.90 CABINET 14.00 POLYURETHANE (RUBBER) FINAL MOUNTING DECK SCREW WASHER STYROFOAM ™ BLOCKS CENTERING BARS DAMPING PADS 15.00 CUTOUT DRYWALL 24.55 CUTOUT DRYWALL COVER/TEMPLATE 16.25 BAFFLE 25.17 BAFFLE S4S OM 10/18/05 12:02 PM Page 9

Page 10 - • Review proper operation of your receiver/amplifier.; ROUBLESHOOTING

10 S YMPTOM S OLUTION If there is no sound from • Check that the receiver/amplifier is on and that a source is playing. any of the speakers: • Check all wires and connections between the receiver/amplifier and the speakers. Make sure all wires are connected. Make sure none of the speaker wires are f...

Page 11 - PECIFICATIONS; 00 Watts per channel

S PECIFICATIONS S4S Frequency Response (–6dB) 20Hz – 150Hz (THX ® /LFE mode) Maximum Recommended Amplifier Power † 500 Watts per channel Impedance 4 Ohms nominal Sensitivity 88dB (2.83V/1m), both woofers driven Woofer Dual 10" polymer-coated aluminum cones w/rubber surrounds Dimensions (H x W x ...