JBL GT6.0c - Manuals - manualsarea.com

Page 3 - ANGLE MOUNT; Line up tab with slot on bracket

03 Component System Parts Your new Component System consists of the GTC04 neodymium magnet tweeter and either a 4", 5-1/4", or 6-1/2" midwoofer. Both the GTC04 and the midwoofer have high-quality passive crossover parts already built into them. Figure 2 is an illustration of the proper w...

Page 4 - Typical installation of the GT4.0c and GT5.0c; as shown in Figure 2a.

04 IN-LINE CROSSOVER(DO NOT CUT OR BYPASS) GTC04 WIRING HARNESS CONNECT TO AMPLIFIER 2 1 Line up tab with slot on bracket Push tweeter into bracket and turn clockwise 2 1 FLUSH MOUNT Midwoofer Terminal Block Connect to Amplifier or head unit Lead from GTC04 tweeter Small 0.11" (-) Terminals Larg...

Page 5 - Tweeter Output Level

05 Tweeter Output Level The GTC04 is a very efficient tweeter. If there is a need to lower the tweeter output level, a pair of 4 ohm / 5 watt resistors can be connected in series with the GTC04 as shown in Figure 3. To avoid short circuits, make sure that heat-shrink tubing or electrical tape is use...

Page 6 - Installation of the GT4.0c woofer; as shown in Figures 4a and 4b.; Figure 4a

06 Installation of the GT4.0c woofer as shown in Figures 4a and 4b. Removable Mounting Ears on GT4.0c Bend up and down repeatedlyto break off or use tin snips. • Some Toyota installations may require mounting ears to be removed from opposite sides.• Some European car installations may require all fo...

Page 7 - Installation of the GT6.0c woofer

07 MountingHooks MountingRing FoamGasket Mounting Slots Rotate to Lock Rotateto Lock Rotateto Lock Slots forMountingHooks MountingHooks Mounting Ring FoamGasket Mounting for US 6-1/2" Honda/ToyotaFactory Location Match Notch on Speaker with Notch on Trim Ring Grille Screen Hole Cutout GrilleTrim...

Page 8 - Figure 5d; Mounting the GT6.0c woofer in; shown in Figures 5d and 5e.

08 Hole Cutout Clips Mounting Surface Figure 5d Figure 5e Mounting the GT6.0c woofer in 165/170mm DIN (European) installations using the Intermount II clips shown in Figures 5d and 5e. Front Mounting Rear Mounting GT4.0c, 5.0c, 6.0c OM 7/16/98 9:54 AM Page 8

Page 9 - Component Placement

09 2. The best center image will be achieved when the distance from the left speaker and the right speakers are as equal as possi- ble from your listening position. This is most easily achieved by placing the speakers as far for- ward as possible. 3. Treble is directional in nature. This means that ...

Page 10 - System Design

10 System Design There are a variety of system options available with the Component System. The simplest configuration is to use them full range with their built-in passive crossovers by connecting them to the output of a head unit or an amplifier (Figures 7 and 8). If you want to build your system ...

Page 11 - Tweeters

11 Installation Warnings and Tips • Be careful not to cut or drill into fuel tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when work- ing on your vehicle. Inspect behind panels before you cut or drill. • Make sure that the midwoofer will physically fit in the mount- ...

Page 13 - Specifications; Component Systems

13 Specifications Component Systems Model GT6.0c GT5.0c GT4.0c Grand Touring Automotive Grand Touring Automotive Grand Touring Automotive 6-1/2" 2-way Component 5-1/4" 2-way Component 4" 2-way Component System System System 1" Titanium Composite 1" Titanium Composite 1" Titan...