Invacare MA60 - Manuals

TYPICAL PRODUCT PARAMETERS MA60 Series 6 Part No 1148137 Environmental Parameters MA60/MA65 OPERATING CONDITIONS AMBIENT TEMPERATURE: RELATIVE HUMIDITY: ATMOSPHERIC PRESSURE: 50° - 95° F 30% - 75% Non-Condensing 70 - 106 kPa STORAGE AND SHIPPING CONDITIONS AMBIENT TEMPERATURE: RELATIVE HUMIDITY: ATM...

LABEL LOCATION Part No 1148137 7 MA60 Series LABEL LOCATION DANGER-EXPLOSION HAZARD: DO NOT use in the presence of flammable anesthetics.CAUTION: Equipment should be connected to a properly grounded receptacle (3-prong). Risk of Electrical shock. DO NOT remove back. Disconnect air hose before admini...

SECTION 1—GENERAL GUIDELINES MA60 Series 8 Part No 1148137 SECTION 1—GENERAL GUIDELINES WARNING SECTION 1 - GENERAL GUIDELINES contains important information for the safe operation and use of this product. Contraindications Always consult the patient’s physician before using the MA60 and MA65 system...

SECTION 1—GENERAL GUIDELINES Part No 1148137 9 MA60 Series Fire Hazard DANGER Smoking DO NOT SMOKE while using this device. This system uses room air for circulation through the mattress. A cigarette can burn a hole in the bed surface and cause damage to the mattress. Also, patient clothing, bed she...

SECTION 2—OPERATION MA60 Series 10 Part No 1148137 SECTION 2—OPERATION CAUTION The control unit and mattress on the MA60 series are designed to be used as a sys- tem. DO NOT replace mattresses or control units with other models or other brands. Otherwise, damage to the system may occur. Contact your...

SECTION 2—OPERATION Part No 1148137 11 MA60 Series FIGURE 2.1 Installing the Powered Mattress Installing the Side Rails WARNING Patient entrapment with bed side rails may cause injury or death. Mattress MUST fit bed frame and side rails snugly to prevent patient entrapment. Follow the manu- facturer...

SECTION 2—OPERATION MA60 Series 12 Part No 1148137 Connecting the Hose CAUTION Ensure that the hose connecting the control unit to the mattress is routed such that it cannot be stepped on, kinked, squeezed or otherwise damaged. NOTE: For this procedure, refer to FIGURE 2.2. 1. Locate the hose at the...

SECTION 2—OPERATION Part No 1148137 13 MA60 Series Connecting the Power Cord WARNING DO NOT alter plug to fit a non-conforming outlet. Instead, have an electrician install a properly grounded 3-prong outlet. Failure to use the correct plug and outlet can result in a potential safety hazard. CAUTION ...

SECTION 2—OPERATION MA60 Series 14 Part No 1148137 Using the Front Panel NOTE: For this procedure, refer to FIGURE 2.3. FIGURE 2.3 Using the Front Panel Power Button 1. To turn the control unit on or off, press and release the Power button ( ). NOTE: Once the unit is plugged in, an AMBER LED on the ...

SECTION 2—OPERATION Part No 1148137 15 MA60 Series Alternating Pressure Button 1. Press the Alternating Pressure button ( ) to select between one of four alternating pressure times - 5, 10, 15 and 20 minutes. NOTE: The alternating pressure times indicate the frequency of deflation or inflation of ha...

SECTION 2—OPERATION MA60 Series 16 Part No 1148137 Firm/Soft Buttons 1. Select comfort pressure settings by pressing Firm ( ) or Soft ( ) button. • Soft Button - Pressing this button reduces the pressure setting in the mattress.• Firm Button - Pressing this button increase the pressure setting in th...

SECTION 2—OPERATION Part No 1148137 17 MA60 Series Max Inflate/Low Air Loss Button MA60 System 1. Press the Max Inflate button ( ) to select the max inflate mode. • Max Inflate Mode - In this mode, the mattress inflates rapidly to maximum firmness (pressurized to 35 ± 6 mmHg). A series of beeps soun...

SECTION 2—OPERATION MA60 Series 18 Part No 1148137 • Alarm Silence mode - Pressing this button silences the alarm that sounds in the event of power failure or when the hose is disconnected from the control unit. NOTE: The Alarm LED illuminates when in this mode. Power Fail LED In the event of power ...

SECTION 2—OPERATION Part No 1148137 19 MA60 Series 9. Verify that the patient has not bottomed out by performing the following steps: A. Ensure that the patient is lying flat on his/her back in the middle of the mattress.B. Place four fingers between the air cushions directly underneath the sacral r...

SECTION 2—OPERATION MA60 Series 20 Part No 1148137 Transferring Patient From/To a Wheelchair WARNING ALWAYS engage the wheel locks of the bed and the wheel locks of the wheelchair before transferring the patient between the bed and the wheelchair. 1. Engage the wheel locks of the bed. Refer to the o...

SECTION 3—MAINTENANCE AND TROUBLESHOOTING Part No 1148137 21 MA60 Series SECTION 3—MAINTENANCE AND TROUBLESHOOTING Cleaning the System WARNING Before cleaning or disassembling the MA60 series, check the underside of the mattress folds for sharp objects such as scissors, needles, etc. These objects s...

SECTION 3—MAINTENANCE AND TROUBLESHOOTING MA60 Series 22 Part No 1148137 CAUTION Laundry workers should always wash their hands before working with clean bedding.DO NOT overload the machine.DO NOT use chlorine bleach because it may damage the fabric coating.High air temperatures will damage the fabr...

SECTION 3—MAINTENANCE AND TROUBLESHOOTING Part No 1148137 23 MA60 Series Troubleshooting PROBLEM CAUSE SOLUTION Mattress not inflating Not alternating properly Mattress hose disconnected Connect hose connectors and lock them in place Air hose kinked or split Unkink hose or replace split hose Major l...

LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer. This warranty is not...