Invacare Infinity LoBack Support - Manuals

Page 2 - WARNING; NOTICE; SAVE THESE INSTRUCTIONS; SPECIAL NOTES; PROCEDURE 2 - PREPARING THE; INSTALLING/REMOVING THE BACK; TABLE OF CONTENTS; PROCEDURE 4 - ADJUSTING THE; SPECIAL NOTES/TABLE OF CONTENTS

2 WARNING THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED BY A QUALIFIED TECHNICIAN. DO NOT INSTALL OR USE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL, DEALER OR TECHNI...

Page 3 - SAFETY SUMMARY; Adjusting the Mounting Hardware/Height; STABILITY WARNINGS; procedure to

3 SAFETY SUMMARY SAFETY SUMMARY SA F E T Y S U MM A R Y NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact your Dealer for further instruction. INSTALLATION WARNINGS Stabilize from the ground up. A stable base, pelvis and footrests are requirements for any torsopositio...

Page 4 - SEATING PRESSURE WARNING

4 SAFETY SUMMARY STABILITY WARNINGS (CONTINUED) ALWAYS make sure wheelchair is stable BEFORE reclining the back system. Rear wheels may haveto be repositioned rearward depending on the degree of recline. ALWAYS ensure stability BEFOREusing maximum amount of recline. TEST wheelchair BEFORE it is occu...

Page 5 - IMPORTANT INFORMATION; FIGURE 1 - INSTALLATION/ADJUSTMENT OVERVIEW; Adjusting the Angle

5 INSTALLATION/ADJUSTMENT OVERVIEW (FIGURE 1) WARNING For proper installation of the Infinity LoBack and to reduce the risk of pressure sores, the adjustmentprocedures in this manual MUST be performed in the following order: 1. Adjusting the Mounting Hardware/Height 2. Adjusting the Depth Hardware I...

Page 6 - PROCEDURE 1; This Procedure includes the following:; Installing Cane Clamps; PREPARING WHEELCHAIR; Removing Cane Clamps

6 PROCEDURE 1 PREPAR I N G W HEE L CHA I R This Procedure includes the following: Installing/Removing Cane Clamps INSTALLING/REMOVING CANECLAMPS (FIGURE 1) WARNING After ANY adjustments, repair or service andBEFORE use, make sure that all attaching hard-ware is tightened securely - otherwise injury ...

Page 7 - PREPARING THE INFINITY LOBACK FOR INSTALLATION; Installing; LATERAL SUPPORTS; DETAIL “A”

7 This Procedure includes the following: Installing/Removing the Lateral Supports Installing/Removing the Back Cushion Installing/Removing the Lower Flap PREPARING THE INFINITY LOBACK FOR INSTALLATION PROCEDURE 2 INSTALLING/REMOVING THELATERAL SUPPORTS (FIGURE 1) WARNING After ANY adjustments, repai...

Page 8 - CAUTION; PROCEDURE 2; Back of; FIGURE 2 - INSTALLING/REMOVING THE BACK CUSHIONS; Bottom of

8 INSTALLING/REMOVING THE BACKCUSHION (FIGURE 2) NOTE: Refer to the INSTALLATION AND STABILITYWARNINGS in the SAFETY SUMMARY of this manual. CAUTION The cushion covers are designed to protect thefoam against moisture and to provide fireretardency. DO NOT use the back without thecovers. If the covers...

Page 9 - Removing

9 PROCEDURE 2 PREPARING THE INFINITY LOBACK FOR INSTALLATION P R EPA R I N G T H E L O B A CK F O R I N S T A LL A T I O N FIGURE 3 - INSTALLING/REMOVING THE MODESTY FLAP 7. Make sure the hook and loop fasteners meet by firmly pushing the TOP of the modesty flap and the BOT-TOM of the cushion togeth...

Page 10 - Installing the Infinity LoBack; FIGURE 1 - INSTALLING/REMOVING THE INFINITY

10 INSTALLING/REMOVING THEINFINITY LOBACK (FIGURE 1) WARNING After ANY adjustments, repair or service andBEFORE use, make sure that all attaching hard-ware is tightened securely - otherwise injury ordamage may result. NOTE: Refer to the INSTALLATION AND STABILITYWARNINGS in the SAFETY SUMMARY of thi...

Page 11 - FIGURE 1 - ADJUSTING THE MOUNTING

11 WARNING For proper installation of the Infinity LoBack andto reduce the risk of pressure sores, the adjust-ment procedures below MUST be performed inthe following order: 1. Adjusting the Mounting Hardware/Height 2. Adjusting the Depth Hardware 3. Adjusting the Angle 4. Adjusting the Lateral Suppo...

Page 12 - Pivoting The Adjustment Brackets (Figure 3); FIGURE 3 - PIVOTING THE ADJUSTMENT

12 PROCEDURE 4 ADJUSTING THE INFINITY LOBACK Pivoting The Adjustment Brackets (Figure 3) 1. Remove the Infinity LoBack from the wheelchair. Refer to INSTALLING/REMOVING THE INFINITYLOBACK in PROCEDURE 3 of this manual, 2. Hold the Infinity LoBack up to the wheelchair. 3. Visually inspect the Infinit...

Page 13 - SIDE VIEW

13 FIGURE 4 - ADJUSTING THE ANGLE B. To DECREASE the angle of the Infinity LoBack, grasp the TOP of the Infinity Loback and pushFORWARD. 4. Torque the two (2) nuts on the two (2) angle brackets to 45-50 in./lbs. 5. Reinstall the back cushion onto the back panel. Re- fer to INSTALLING/REMOVING THE BA...

Page 15 - FIGURE 4 - REPLACING THE BACK; INSPECTION; CLEANING; Cover; Foam

15 This Procedure includes the following: Installing/Remove Back Cushion Foam Inspection Cleaning REPLACING THE BACK CUSHIONFOAM (FIGURE 1) NOTE: Refer to the INSTALLATION AND STABILITYWARNINGS in the SAFETY SUMMARY of this manual. 1. Remove the back cushion from the back panels. Refer to INSTALLING...

Page 16 - LIMITED WARRANTY

Invacare Corporation www.invacare.com USA Canada One Invacare Way 5970 Chedworth Way Invacare is a registered trademark of Invacare Corporation. Elyria, Ohio USA Mississauga, Ontario © 1999 Invacare Corporation 44036-2125 L5R 3T9, Canada 800-333-6900 905-890-8838 Form No. 99-221 Part No. 1095174 Rev...