Invacare 1073955 - Manuals

Part No. 1073955 7 Orbit ™ Name _______________________________________________________________ Address _____________________________________________________________ City ___________________ State/Province __________ Zip/Postal Code ________ Email ___________________________________ Phone No. ______...

Orbit ™ 8 Part No. 1073955 Fold here Fold here Cut Along Line Invacare Product Registration Form Please Seal with Tape Before Mailing

SPECIAL NOTES Part No. 1073955 9 Orbit ™ SPECIAL NOTES Signal   words   are   used   in   this   manual   and   apply   to   hazards   or   unsafe   practices   which   could   result   in   personal   injury   or   property   damage.   Refer   to   the   following   table   for   definitions   of  ...

LABEL LOCATION Orbit ™ 10 Part No. 1073955 LABEL LOCATION Standard Labels WARNING DO NOT OPERATE WITHOUT THE ANTI-TIP TUBES INSTALLED. REV. 5/98 P/N 60106X144 Refer to Owner's Manualfor proper anti-tippersetting. 1085379 WARNING NOTE:   Seat   removed   for   clarity. WEIGHT CAPACITY 150 LBS. (68 kg...

LABEL LOCATION Part No. 1073955 11 Orbit ™ Wheelchairs with TRRO P/N 1120033 REV B - 08/05 Refer to attached TRANSPORT READY OPTION Instruction Card and wheelchair Owner's Manual before use. NOTE:   Seat   removed   for   clarity.

TYPICAL PRODUCT PARAMETERS Orbit ™ 12 Part No. 1073955 TYPICAL PRODUCT PARAMETERS *NOTE:   Invacare   recommends   that   rear   seat ‐ to ‐ floor   height   be   at   least   3/8   inch   shorter   than   front   seat ‐ to ‐ floor   height.   Otherwise   a   forward   seat   dump   can   occur.   T...

SECTION 1—GENERAL GUIDELINES Part No. 1073955 13 Orbit ™ SECTION 1—GENERAL GUIDELINES WARNING SECTION 1 - GENERAL GUIDELINES contains important information for the safe operation and use of this product. DO NOT use this product or any available optional equipment without first completely reading and...

SECTION 1—GENERAL GUIDELINES Orbit ™ 14 Part No. 1073955 Anti-Tippers Anti ‐ tippers   MUST   be   attached   at   all   times.   Inasmuch   as   the   anti ‐ tippers   are   an   option   on   this   wheelchair   (you   may   order   with   or   without   the   anti ‐ tippers),   Invacare   strongl...

SECTION 1—GENERAL GUIDELINES Part No. 1073955 15 Orbit ™ DO   NOT   attempt   to   stop   a   moving   wheelchair   with   wheel   locks.   Wheel   locks   are   not   brakes. DO   NOT   tip   the   wheelchair   without   assistance. DO   NOT   use   an   escalator   to   move   a   wheelchair   bet...

SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Orbit ™ 16 Part No. 1073955 SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Safety/Handling of Wheelchairs Safety   and   handling   of   the   wheelchair   require   the   close   attention   of   the   wheelchair   user   as   well   as   the   assistant.   This  ...

SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1073955 17 Orbit ™ Coping With Everyday Obstacles Coping   with   the   irritation   of   everyday   obstacles   can   be   alleviated   somewhat   by   learning   how   to   manage   your   wheelchair.   Keep   in   mind   your   center   of   gravi...

SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Orbit ™ 18 Part No. 1073955 Reaching, Leaning and Bending Forward WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees. NOTE:   For   this   procedure,   refer   to ...

SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1073955 19 Orbit ™ Method 1 - Wheelchair With Step Tubes NOTE:   For   this   procedure,   refer   to   FIGURE 2.3. Place   foot   on   the   step   tube   and   begin   to   tilt   the   wheelchair   toward   you.   Apply   a   continuous   downward...

SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Orbit ™ 20 Part No. 1073955 WARNING When lowering the front casters of the wheelchair, DO NOT let the wheelchair drop the last few inches to the ground. This could result in injury to the occupant and/or damage to the wheelchair. Roll   the   wheelchair   bac...

SECTION 2—SAFETY/HANDLING OF WHEELCHAIRS Part No. 1073955 21 Orbit ™ 3. The   second   assistant,   with   a   firm   hold   on   a   non ‐ detachable   part   of   the   framework,   lifts   the   wheelchair   up   and   over   the   stair   and   steadies   the   wheelchair   as   the   first   as...

SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Orbit ™ 22 Part No. 1073955 SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING NOTE:   Every   six   months   or   as   necessary,   take   your   wheelchair   to   a   qualified   technician   for   a   thorough   inspection   and   servicing.   Regular   cleani...

SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1073955 23 Orbit ™ ❑ Inspect   handrims   for   signs   of   rough   edges   or   peeling. ❑ Inspect   axle   assembly   for   proper   tension   by   spinning   caster.   Caster   should   come   to   a   gradual   stop. ❑ Adjust   front   caster...

SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Orbit ™ 24 Part No. 1073955 ❑ Check   that   the   wheel   lock   pivot   points   are   free   of   wear   and   looseness. ❑ Inspect   seat   and   back   for   loose   or   broken   hardware. ❑ Inspect   seat   positioning   strap   for   any   signs   ...

SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Part No. 1073955 25 Orbit ™ Troubleshooting Maintenance Maintenance Safety Precautions WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely. CAUTION DO NOT overtighten hardware attaching to...

SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING Orbit ™ 26 Part No. 1073955 WARNING DO NOT use the wheelchair unless it has the proper tire pressure (P.S.I.). DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm. 5. If   tires   are   pneu...

SECTION 4—ASSEMBLY Part No. 1073955 27 Orbit ™ SECTION 4—ASSEMBLY WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. Assembling/Disassembling the Removable Orbit Wheelchair NOTE:   For   this ...

SECTION 4—ASSEMBLY Orbit ™ 28 Part No. 1073955 WARNING The locking pins MUST be protruding past the top of the seat plate assembly for a positive lock.Keep locking pins clean. 10. Push   in   on   the   tip   of   the   quick ‐ release   pin   and   reinstall   in   the   seat/base   frame   plate  ...

SECTION 4—ASSEMBLY Part No. 1073955 29 Orbit ™ FIGURE 4.1 Assembling/Disassembling the Removable Orbit Wheelchair Locking Channel Seat Frame Base Frame Base Frame Plate Locking Button Locking Buttons Engage Here Seat Frame Plate DETAIL “A” - SECTIONAL OF SEAT FRAME AND BASE FRAME ASSEMBLED (WITHOUT ...

SECTION 5—FRONT RIGGINGS Orbit ™ 30 Part No. 1073955 SECTION 5—FRONT RIGGINGS WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. Installing/Removing Front Riggings NOTE:   For   this   procedu...

SECTION 5—FRONT RIGGINGS Part No. 1073955 31 Orbit ™ Adjusting Footplate Height NOTE:   Release   the   footrest   locking   mechanism   and   lift   the   mounting   pin   out   of   the   mounting   tube.   Lay   the   assembly   on   a   flat   surface   to   simplify   this   procedure. Adjustin...

SECTION 5—FRONT RIGGINGS Orbit ™ 32 Part No. 1073955 WARNING DO NOT overtighten. Footrest must be able to rotate upward from the horizon- tal to vertical position. 4. Reinstall   the   mounting   screw   through   the   mounting   holes   of   the   footplate   and   footrest   support. 5. Secure   ...

SECTION 5—FRONT RIGGINGS Part No. 1073955 33 Orbit ™ Installing Elevating Legrest NOTE:   For   this   procedure,   refer   to   FIGURE 5.5. 1. Insert   the   pivot   tube   into   the   legrest   support   and   secure   it   with   the   bolt   and   nut. 2. Place   legrest   on   the   outside   ...

SECTION 5—FRONT RIGGINGS Orbit ™ 34 Part No. 1073955 Installing/Adjusting the Adjustable Angle Flip-up Footplates WARNING When determining the angle of the footplates, make sure the rear of the footplates do not interfere with the movement of the front casters. NOTE:   For   this   procedure,   refe...

SECTION 5—FRONT RIGGINGS Part No. 1073955 35 Orbit ™ FIGURE 5.8 Adjusting Depth on Adjustable Angle Flip-Up - Adjusting Angle on Adjustable Angle Flip-up Footplate Adjusting Perpendicular and/or Inversion/Eversion Adjustable Angle Flip-up Footplate NOTE:   For   this   procedure,   refer   to   FIGU...

SECTION 5—FRONT RIGGINGS Orbit ™ 36 Part No. 1073955 4. Secure   the   bilateral   contracture   platform   to   the   seat   frame   in   the   mounting   position   shown   in   FIGURE 5.10   with   the   mounting   screws   and   washers   provided.    Securely   tighten. 5. Adjust   the   bilate...

SECTION 5—FRONT RIGGINGS Part No. 1073955 37 Orbit ™ FIGURE 5.11 Adjusting Height of Bilateral Contracture Platform Adjusting Bilateral Contracture Platform Angle 1. Remove   the   two   mounting   screws   and   locknuts   that   secure   the   upper   support   of   the   bilateral   contracture  ...

SECTION 5—FRONT RIGGINGS Orbit ™ 38 Part No. 1073955 FIGURE 5.12 Replacing Sector Block Installing/Removing/Adjusting the Telescoping Front Frame Tubes NOTE:   For   this   procedure,   refer   to   FIGURE 5.13   on   page   39. Installing/Removing Telescoping Front Frame Tubes 1. If   necessary,   ...

SECTION 5—FRONT RIGGINGS Part No. 1073955 39 Orbit ™ FIGURE 5.13 Installing/Removing/Adjusting the Telescoping Front Frame Tubes Optional Footrest Accessories Replacing Heel Loop Composite Footplates NOTE:   For   this   procedure,   refer   to   FIGURE 5.14. 1. Remove   the   mounting   screw   and...

SECTION 5—FRONT RIGGINGS Orbit ™ 40 Part No. 1073955 Adjustable Footplate NOTE:   For   this   procedure,   refer   to   FIGURE 5.15. 1. Remove   the   four   mounting   screws   and   washers   that   secure   the   existing   heel   loop   to   the   footplate. 2. Position   the   mounting   holes...

SECTION 6—ARMS Part No. 1073955 41 Orbit ™ SECTION 6—ARMS WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. Installing the T-Arm Sockets NOTE:   For   this   procedure,   refer   to   FIGURE ...

SECTION 6—ARMS Part No. 1073955 43 Orbit ™ Adjusting the T-Arms Adjusting T-Arm Height NOTE:   For   this   procedure,   refer   to   FIGURE 6.3. 1. Unlock   the   T ‐ arm   by   flipping   the   T ‐ arm   release   lever   towards   the   inside   of   the   wheelchair. NOTE:   If   necessary,   pu...

SECTION 6—ARMS Orbit ™ 44 Part No. 1073955 2. Rotate   the   arm   pad   180 o   and   reposition   the   arm   pad   on   the   arm   tube.   3. Re ‐ secure   the   arm   pad   to   the   arm   tube   with   the   two   mounting   screws.   Securely   tighten. 4. Repeat   STEPS   1 ‐ 3   for   the ...

SECTION 6—ARMS Part No. 1073955 45 Orbit ™ FIGURE 6.5 Adjusting the T-Arms - Adjusting T-Arm Depth Adjusting T-Arm Sockets NOTE:   For   this   procedure,   refer   to   FIGURE 6.6. 1. Remove   the   rear   wheels   from   the   wheelchair.   Refer   to   Removing/Installing   Rear   Wheels   on   p...

SECTION 6—ARMS Orbit ™ 46 Part No. 1073955 FIGURE 6.6 Adjusting the T-Arms - Adjusting T-Arm Sockets Adjusting the Transfer Assists and/or Side Guards NOTE:   For   this   procedure,   refer   to   FIGURE 6.7   on   page   47. 1. Remove   the   T ‐ arm   from   the   wheelchair.   Refer   to   Insta...

SECTION 6—ARMS Part No. 1073955 47 Orbit ™ 4. Re ‐ secure   the   side   guard   to   the   bottom   clamp   with   the   two   bottom   mounting   screws.   Securely   tighten. 5. Install   the   T ‐ arm   onto   the   wheelchair.   Refer   to   Installing/Removing   the   T ‐ arms    on   page 42....

SECTION 6—ARMS Orbit ™ 48 Part No. 1073955 WARNING DO NOT over tighten the locknut that secures the locking lever to the bottom bracket. Over tightening this locknut will prevent the locking lever from operating properly, possibly causing injury. 7. Install   the   phillips   bolt   and   tighten   ...

SECTION 6—ARMS Part No. 1073955 49 Orbit ™ Installing/Removing/Adjusting Catilever Arms NOTE:   To   remove,   reverse   this   procedure. NOTE:   When   removing   the   locknuts   and   washers   from   the   cantilever   arm   assembly,   leave   the   top   mounting   screw,   coved   washers   ...

SECTION 6—ARMS Orbit ™ 50 Part No. 1073955 Replacing/Repositioning the Locking Mechanism in the Cantilever Arm NOTE:   For   this   procedure,   refer   to   FIGURE 6.10   on   page   50. CAUTION The locking mechanism is spring loaded. Place your free hand over the locking mechanism to prevent parts...

SECTION 6—ARMS Part No. 1073955 51 Orbit ™ Replacing and Adjusting Arm Pad Depth for Cantilever Arms NOTE:   For   this   procedure,   refer   to   FIGURE 6.11. Adjustment 1. Remove   the   mounting   screw   from   the   rear   of   the   armrest   pad   and   self ‐ taping   screw   if   full   le...

SECTION 7—SEAT AND BACK Orbit ™ 52 Part No. 1073955 SECTION 7—SEAT AND BACK WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. NOTE:   The   procedures   in   this   section   of   the   manua...

SECTION 7—SEAT AND BACK Part No. 1073955 53 Orbit ™ Installing Fixed Height Stroller Handles NOTE:   For   this   procedure,   refer   to   FIGURE 7.2. 1. Remove   the   back   cane   grip   and   plug   button   from   the   back   cane. 2. Slide   the   stroller   handle   into   the   back   cane...

SECTION 7—SEAT AND BACK Orbit ™ 54 Part No. 1073955 Removing Adjustable Angle Stroller Handles 1. Remove   the   two   mounting   screws   that   secure   the   adjustable   height   stroller   handle   to   the   back   canes. 2. Remove   the   adjustable   angle   stroller   handle   from   the   ...

SECTION 7—SEAT AND BACK Part No. 1073955 55 Orbit ™ FIGURE 7.4 Adjusting Adjustable Angle Stroller Handles Removing/Installing the Spreader Bar NOTE:   For   this   procedure,   refer   to   FIGURE 7.5   on   page   56. NOTE:   For   removing   and   installing   the   spreader   bar   on   the   re...

SECTION 7—SEAT AND BACK Orbit ™ 56 Part No. 1073955 CAUTION When reattaching back assembly, DO NOT OVERTIGHTEN! Back will not fold down properly. Tighten hardware until snug. 10. Reattach   back   assembly   to   the   back   angle   bracket   with   the   existing   mounting   screws,   spacers,   ...

SECTION 7—SEAT AND BACK Part No. 1073955 57 Orbit ™ Installing/Removing a Seating System NOTE:   If   a   seating   system   is   being   used   on   the   wheelchair,   refer   to   your   particular   seating   system   manufacturer ʹ s   Owner ʹ s   Manual   for   installation   and   removal   o...

SECTION 8—FRONT CASTERS Orbit ™ 58 Part No. 1073955 SECTION 8—FRONT CASTERS WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. CAUTION DO NOT overtighten hardware attaching to the frame. Damag...

SECTION 8—FRONT CASTERS Part No. 1073955 59 Orbit ™ Replacing Front Fork NOTE:   For   this   procedure,   refer   to   FIGURE 8.2. 1. Remove   the   front   caster   assemblies   from   the   wheelchair.   Refer   to   Replacing/Installing   Front   Caster   Assemblies   on   page 58. 2. Remove   t...

SECTION 8—FRONT CASTERS Orbit ™ 60 Part No. 1073955 Adjusting Caster Headtubes NOTE:   For   this   procedure,   refer   to   FIGURE 8.3. NOTE:   Caster   headtubes   that   are   perpendicular   to   the   floor   will   roll   better,   track   straighter   and   minimize   any  ʺ 3 ‐ wheeling ʺ  ...

SECTION 9—REAR WHEELS Part No. 1073955 61 Orbit ™ SECTION 9—REAR WHEELS WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. Removing/Installing Rear Wheels NOTE:   For   this   procedure,   ref...

SECTION 9—REAR WHEELS Orbit ™ 62 Part No. 1073955 FIGURE 9.1 Removing/Installing Rear Wheels Adjusting the Quick-Release Axle NOTE:   For   this   procedure,   refer   to   FIGURE 9.2. 1. Remove   rear   wheel   and   quick ‐ release   axle   from   the   wheelchair.   Refer   to   Removing/Installi...

SECTION 9—REAR WHEELS Part No. 1073955 63 Orbit ™ Replacing Handrims Non-Projection Handrims NOTE:   For   this   procedure,   refer   to   FIGURE 9.3. NOTE:   The   following   procedures   will   work   for   any   type   of   projection   handrim. Removing Non-Projection Handrims 1. Remove   rear...

SECTION 9—REAR WHEELS Orbit ™ 64 Part No. 1073955 Installing Projection Handrims 1. If   necessary,   remove   rear   wheels   from   the   wheelchair.   Refer   to   Removing/Installing   Rear   Wheels   on   page 61. 2. If   necessary,   remove   the   existing   handrim   from   the   rear   whee...

SECTION 10—ANTI-TIPPERS/WHEEL LOCKS Part No. 1073955 65 Orbit ™ SECTION 10—ANTI-TIPPERS/WHEEL LOCKS WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. Foot Activated Wheel Lock Procedures NOTE...

SECTION 10—ANTI-TIPPERS/WHEEL LOCKS Orbit ™ 66 Part No. 1073955 FIGURE 10.1 Foot Activated Wheel Lock Procedures Hand Activated Wheel Lock Procedures Installing/Removing Hand Activated Wheel Locks NOTE:   For   this   procedure,   refer   to   FIGURE 10.3   on   page   67. 1. Remove   the   foot   a...

SECTION 10—ANTI-TIPPERS/WHEEL LOCKS Part No. 1073955 67 Orbit ™ Engaging/Disengaging Hand Activated Wheel Locks NOTE:   For   this   procedure,   refer   to   FIGURE 10.3. 1. Push   handle   forward   away   from   tire   to   engage   wheel   locks. 2. Pull   handle   back   toward   tire   to   di...

SECTION 10—ANTI-TIPPERS/WHEEL LOCKS Orbit ™ 68 Part No. 1073955 FIGURE 10.4 Adjusting the Wheel Lock Installing Anti-Tippers NOTE:   For   this   procedure,   refer   to   FIGURE 10.5. NOTE:   A   1/2 ‐ inch   clearance   between   the   bottom   of   the   anti ‐ tipper   wheels   and   the   floor...

SECTION 10—ANTI-TIPPERS/WHEEL LOCKS Part No. 1073955 69 Orbit ™ Adjusting Anti-Tippers NOTE:   For   this   procedure,   refer   to   FIGURE 10.6. NOTE:   The   anti ‐ tippers   must   maintain   a   1 ‐ 1/2   to   2 ‐ inch   clearance   between   the   bottom   of   the   anti ‐ tipper   wheels   a...

SECTION 11—RECLINER Orbit ™ 70 Part No. 1073955 SECTION 11—RECLINER WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. Engaging Tilt-In-Space WARNING After ANY adjustments, repair or service a...

SECTION 11—RECLINER Orbit ™ 72 Part No. 1073955 FIGURE 11.1 Engaging Tilt-In-Space Operating Recliner WARNING Pinch Points exist between spreader bar and gas cylinders. Use caution, otherwise injury may occur. NOTE:   For   this   procedure,   refer   to   FIGURE 11.2   on   page   73. 1. Make   sur...

SECTION 11—RECLINER Part No. 1073955 73 Orbit ™ 7. When   the   back   reaches   desired   angle,   slowly   release   the   handles   of   the   recliner   cable   assemblies. 8. To   return   the   back   to   the   full   upright   position,   reverse   the   above   steps   keeping   in   mind  ...

SECTION 11—RECLINER Orbit ™ 74 Part No. 1073955 Adjusting Posterior (Rearward) Limit Stops NOTE:   For   this   procedure,   refer   to   FIGURE 11.3 WARNING Contact a healthcare professional or assistant for allowable tilt angles that are suitable for the occupant. 1. Engage   both   wheel   locks....

SECTION 11—RECLINER Part No. 1073955 75 Orbit ™ FIGURE 11.4 Replacing Upholstery (Recliner Models Only) Adjusting the Back Height - Recliner Models Only NOTE:   For   this   procedure,   refer   to   FIGURE 11.5. 1. If   necessary,   remove   the   rear   wheels.   Refer   to   Removing/Installing  ...

SECTION 12—TRANSPORT READY OPTION Orbit ™ 76 Part No. 1073955 SECTION 12—TRANSPORT READY OPTION WARNING Contact Invacare Corporation (800-333-6900) with any questions about using this wheelchair for seating in a motor vehicle.When feasible, wheelchair occupants should transfer into the vehicle seat ...

SECTION 12—TRANSPORT READY OPTION Part No. 1073955 77 Orbit ™ About Transport Ready Packages TRRO   includes   four   factory ‐ installed   transport   brackets   and   a   wheelchair   anchored   pelvic   belt.   TRRO   has   been   crash ‐ tested   in   accordance   with   ANSI/RESNA   WC   Vol   ...

SECTION 12—TRANSPORT READY OPTION Orbit ™ 78 Part No. 1073955 Securing the Wheelchair to the Vehicle Positioning the Wheelchair in the Vehicle WARNING This wheelchair must be in a forward facing position during travel in a motor vehicle.The recommended clear zones for wheelchair seated occupants res...

SECTION 12—TRANSPORT READY OPTION Part No. 1073955 79 Orbit ™ Securement Points FIGURE 12.1 Securement Points Securing the Wheelchair This   wheelchair   is   to   be   used   only   with   Wheelchair   Tie ‐ down   and   Occupant   Restraint   Systems   (WTORS)   that   have   been   installed   in...

SECTION 12—TRANSPORT READY OPTION Orbit ™ 80 Part No. 1073955 Securing the Occupant Vehicle-Anchored Belts NOTE:   For   this   procedure,   refer   to   FIGURE   12.2. This   wheelchair   has   an   overall   rating   of   “B”   with   regard   to   accommodating   the   use   and   fit   of   vehi...

SECTION 12—TRANSPORT READY OPTION Part No. 1073955 81 Orbit ™ Positioning Belts WARNING The angle of the pelvic belt should be within the preferred zone of 45 to 75 degrees to the horizontal or within the optional zone of 30 to 45 degrees to the horizontal.Steeper side-view pelvic belt angles are es...

SECTION 13—OPTIONS Orbit ™ 82 Part No. 1073955 SECTION 13—OPTIONS WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur.RECLINER MODELS ONLY - If the ventilator, ventilator battery, or ventilator ...

LIMITED WARRANTY Part No. 1073955 83 Orbit ™ LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.This warranty is extended only to the original purchaser who purchases this product when new and unused fro...