Ingersoll Rand VL2-100 - Manuals

MHD56012 - Edition 8 5 INSTALLATION Prior to installing hoist, carefully inspect it for possible shipping damage. Hoists are supplied fully lubricated from the factory. Lubrication of the load chain is recommended before initial hoist operation. • Depending on model selected, hoist may weigh up to 4...

6 MHD56012 - Edition 8 • The clicking sound of the pawl on the ratchet gear is normal when a load is being raised. Storing the Hoist 1. Always store hoist in a no load condition. 2. Wipe off all dirt and water. 3. Oil the chain, hook pins and hook latch pins. 4. Hang in a dry place. 5. Before return...

MHD56012 - Edition 8 7 3. HOOK LATCHES. Check operation of hook latches. Replace if broken or missing. 4. CHAIN. Refer to Dwg. MHP0102 on page 7. Examine each link for bending, cracks in weld areas or shoulders, transverse nicks and gouges, weld splatter, corrosion pits, striation (minute parallel l...

MHD56012 - Edition 8 9 Load Chain • Failure to maintain clean and well lubricated load chain may result in chain failure causing injury, death or substantial property damage. 1. Lubricate each link of chain weekly. Apply new lubricant over existing layer. 2. In severe applications or corrosive envir...

10 MHD56012 - Edition 8 (Dwg. MHP0043) Attaching End of Load Chain Refer to Dwg. MHP0410 on page 10.1. Push end pin (20) “in”, towards end spring (19). Remove end anchor A (21). 2. Slide end link of load chain (47) on end anchor A (21) shaft. 3. Place end anchor A (21) shaft into end anchor B (22) g...

MHD56012 - Edition 8 11 General Disassembly The following instructions provide necessary information to disassemble, inspect, repair, and assemble the hoist. Hoist assembly parts drawings are provided in “PARTS” section. If a hoist is being completely disassembled for any reason, follow the order of...

12 MHD56012 - Edition 8 8. Install hand chain (46) in handwheel (31). Make sure hand chain (46) is seated properly. 9. Install “looped” end of a hand chain guide (35) over each of the two upper stay bolts on side plate 1 (1). Hand chain guides (35) must be positioned like two “Ls” pointing inward (“...

MHD56012 - Edition 8 13 15 AND 20 TON TOP AND BOTTOM HOOK ASSEMBLY DRAWING 15 ton VL2 Top and Bottom Hook (Dwg. MHP0046) 20 ton VL2 Top and Bottom Hook (Dwg. MHP0047)

14 MHD56012 - Edition 8 HOIST ASSEMBLY PARTS DRAWING (Dwg. MHP0045) Connect Lo a d Ch a in

MHD56012 - Edition 8 15 HOIST ASSEMBLY PARTS LIST ITEM NO. DESCRIPTIONOF PART QTY. TOTAL PART NO. 1/2 ton 1 ton 1-1/2 ton 2 ton 3 ton 5, 8, 10, 15 & 20 ton 1 Side Plate 1 Assembly (Incl’s item 5) 1(2) 71029169 71029201 71029177 71029185 71029177 71029193 5 Needle Bearing w/Retainer Ring 2(4) 237...

18 MHD56012 - Edition 8 HOIST OVERLOAD CLUTCH ASSEMBLY DRAWING AND PARTS LIST (Dwg. MHP0322) Refer to Hoist Assembly Parts List on pages 15 and 16 for items shown on drawing. ITEM NO. DESCRIPTIONOF PART QTY. TOTAL PART NUMBER 1/2 ton 1 ton 1-1/2 ton 2 ton 3 ton 5, 8, 10, 15 & 20 ton 31 Handwheel...

20 MHD56012 - Edition 8 Old Style Parts for this style chain container assembly may be obsolete or out of production and may not be available. ACCESSORIES VL2 HOIST REVISIONS VL2 Hoists manufactured prior to 1990 were supplied with a clip which was installed on wheel cover (38) and was held in posit...

MHD56012 - Edition 8 21 CHAINING INFORMATION Note: The 20 ton hoist is similar to the 15 ton hoist but uses one extra idle sheave on the top and bottom hook frames and has eight chain falls. PARTS ORDERING INFORMATION Use of other than genuine Ingersoll-Rand replacement parts may result in decreased...

MHD56012 - Edition 8 23 WARRANTY Ingersoll-Rand Company ( I-R ) warrants to the original user its Hoists and Winches (Products) to be free of defects in material and workmanship for a period of one year from the date of purchase. I-R will repair, without cost, any Product found to be defective, incl...