Page 2 - Contents
2 Contents 1. Safety Cautions 3 4 5 6 7~8 9 10 11 12~13 14 15~16 17~20 21 22 23 8. Washing the Ice Maker Power supply related items 9. Maintenance of the Ice Maker Installation related items 10. Specifications 11. Troubleshooting guide 2. Part names 3. Installation specifications Gravity Drain Pipe ...
Page 4 - ■ Power supply related items ■
4 ■ Power supply related items ■ Avoid putting any object onthe power cord and make sure that the cord does not get tangled or tied. It may cause fire or electricshock. Oh! NO Stop using the product if the power cord is damaged. It may cause fire or electric shock. Oh! NO Do not touch any electrical...
Page 5 - ■ Installation related items ■
5 ■ Installation related items ■ The ice maker provides optimal functionality at room temperature of 10~20℃ and supplied water temperature of lower than 10℃. It may damage the product. Room temperature of 10~20℃ Temperature of supplied water: lower than 10℃ Keep away any heating appliance from the p...
Page 7 - Installation specifications; Space requirements for installation; Requirements for power supply; Caution
7 3. Installation specifications Fig. 1 Front View Fig. 2 Side View Fig. 3 Top View Space requirements for installation When moving the ice maker, check whether the prepared opening dimensions,electric power, and piping position are correct. Refer to the installation specifications and drawings show...
Page 8 - Requirements for plumbing
8 Requirements for plumbing Plan the arrangement of the water supply pipes.Connect a 1/4" diameter copper cable with the tap water pipe.Install a shutoff valve between the tap water pipe and the product so that the user can operate the valve. Do not install the shutoff valve at the back of the p...
Page 9 - Gravity Drain Pipe Model
9 Fig. 4 Top View Fig. 5 Front View Before connecting the drain tube and the water supply pipe with the ice maker, pipes should necessarily be arranged. The horizontal distance of the drain tube should be 1/4" at every 12" (305) distance. An air gap is required between the drainage tube of t...
Page 10 - Drain Pump Model
10 Drain pump kit You may order the ice maker with orwithout a drain pump. In the case of themodel with no drain pump, water is drained by gravity.However, it is possible to install a drainpump kit on the gravity drain pipe model if you wish convert the model to a drain pump model.You may obtain the...
Page 11 - What to check prior to installation; ■ Follow this process! ■
11 4. What to check prior to installation ■ Follow this process! ■ 230V~50Hz Water source valve Water source tube Drain hose - The water supply valve may have different shapes depending on the installation condition.- The filter may be located close to the water source or back of the product dependi...
Page 12 - Changing Door-opening Method; Installation of the Product
12 Changing Door-opening Method The direction in which the door fixed with hinges opens may be changed.The hinges are attached to the right-hand side of the door when the product is shippedfrom the factory.However, the ice maker is designed so that the hinges may be installed on either side. If the ...
Page 13 - Installation Checklist; Warning
13 Installation Checklist Important Information : The installation engineer should check whether any installation part ha been omitted and follow the check list below to ensure safe and proper installation. If you have any questions or problems regarding installation, address your queries to the dis...
Page 15 - Guide to Operating the Ice Maker; Initial operation; Ice
15 7. Guide to Operating the Ice Maker Fig. 10 Switch Fig. 11 Ice cube Initial operation ① Open the water supply valve connected with the ice maker.② Insert the plug of the ice maker into the electric outlet.③ Open the door and turn the switch at the lower end of the product to the “ICE” position.”④...
Page 17 - ■ Cleaning the nozzle / ice slide / water tank ■; Slightly lift the ice slide to remove it.; Washing the Ice Maker
17 ■ Cleaning the nozzle / ice slide / water tank ■ 1. Open the door and remove two front injection bolts on the top cover. 2. Pull the top cover to remove it. 3. Slightly lift the ice slide to remove it. 4. Clean the slide with soft plastic brush or sponge. 8. Washing the Ice Maker
Page 18 - ■ Cleaning the filters of the water tank and ice tank ■
18 ■ Cleaning the filters of the water tank and ice tank ■ 5. Clean the gap of the nozzle frame fixed on the vessel sheet (water tank). 6. Lift the drain projectile inside the vessel sheet (water tank), clean it, and drain the water. * Make sure that the drain projectile is assembled back in the cor...
Page 20 - ■ Cleaning the condenser ■
20 Cleaning the condenser - Cleaning at least once a month after turning off power ■ Cleaning the condenser ■ 2. Remove dust from the surface of the condenser with a vacuum cleaner for home use or a portable cleaner. 1. Remove two screws on the front panel at the center of the inside. 3. Reassemble ...
Page 21 - Management in the coldest season; Adjusting the ice maker; Maintenance of the Ice Maker
21 Management in the coldest season ① Clean the ice-production system. ② Turn off the power. ③ Empty the water container. Remove the pump hose. The pump hose may be removed after removing the back panel from the ice maker. ④ Separate the inlet pipe connected with the water supply valve. ⑤ Turn on th...
Page 23 - Troubleshooting guide
23 11. Troubleshooting guide PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Ice maker does not operate Ice maker is unplugged Plug ice maker in. Breaker tripped Reset breaker - if it happens again, call a authorized service center. Switch turned to “OFF” Turn switch to “ICE”. The ice tank is full. The ice...
