Husky HU80520 - Manuals

6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical replacement parts. The operation of ...

7 FEATURES Fig. 1 PRODUCT SPECIFICATIONS Engine .......................................................................................................................................... Briggs and Stratton Q45™*Fuel Tank Capacity ........................................................................

8 FEATURES KNOW YOUR PRESSURE WASHER See Figure 1. The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating feature...

9 INSTALLING THE TELESCOPING HANDLE See Figure 3. To install the telescoping handle:  Align the arrows on the U-shaped handle with the arrows on the back of the frame.  Push and hold the button on the handle as you slide the handle into the holes in the frame.  Lock the handle in place by alignin...

10 ASSEMBLY ADDING OIL TO THE ENGINE See Figure 4. NOTE: This machine has been shipped with approximately 2 oz. of oil in the engine from testing. You must add oil to the engine before starting it the first time. CAUTION: Any attempt to start the engine without adding oil will result in engine failu...

11 ASSEMBLY ATTACHING INJECTION HOSE See Figure 6. Before detergent can be used with this machine, the injection hose must be attached.  Push the open end of the clear injection hose securely over the fitting as shown in figure 7.  Place the filtered end of the injection hose in the bottle of dete...

12 ASSEMBLY CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP See Figure 9. ������After the high pressure hose has been uncoiled and attached to the spray wand:  Align the collar on the threaded nipple on the pump.  Insert the nozzle on the end of the high pressure hose collar into the threaded nipple...

13 OPERATION APPLICATIONS You may use this tool for the purposes listed below:  �Removing dirt and mold from decks, cement patios, and house siding  �Cleaning cars, boats, motorcycles, outdoor furniture, and grills STARTING AND STOPPING THE PRESSURE WASHER See Figures 11 - 12. CAUTION: Do not run ...

14 OPERATION Fig. 13 USING THE SPRAY WAND TRIGGER See Figure 13. �� For greater control and safety, keep both hands on the spray wand at all times.  Pull back and hold the trigger to operate the pressure washer.  Release the trigger to stop the flow of water through the nozzle. To engage the lock ...

15 OPERATION Fig. 16 MOVING THE PRESSURE WASHER See Figure 16. NOTE: Never lift or carry this product using the moving handle.  Turn the pressure washer off.  Standing at the back of the machine, grasp the handle firmly with both hands and pull the handle up until it locks into place with a “click...

16 MAINTENANCE WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear...

17 Fig. 19 OIL DRAIN PLUG CONTAINER MAINTENANCE CHANGING THE OIL See Figure 19. NOTE: Run the engine out of gas to prevent gas spills if machine is tilted. Allow 30 minutes of “cool down” time.  �Place a container under the pressure washer.  Remove th e oil drain plug and drain the old oil. NOTE: ...

18 MAINTENANCE STORING THE PRESSURE WASHER It is important to store this product in a frost-free area. Always empty water from all hoses, the pump, and the detergent bucket before storing. NOTE: Use of a fuel stabilizer and pump saver will give you better performance and increase the life of the mac...

19 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine fails to start 1. No fuel in tank 1. Fill tank 2. Spark plug shorted or fouled 2. Replace spark plug 3. Spark plug is broken (cracked 3. Replace spark plug porcelain or electrodes broken) 4. Ignition lead wire shorted, broken, 4. Replace lead wire or ...

21 WARRANTY LIMITED NON-ENGINE WARRANTY STATEMENT Techtronic Industries North America, Inc. warrants to the original retail purchaser that this HUSKY ® brand pressure washer is free from defect in material and workmanship and agrees to repair or replace, at Techtronic Industries North America, Inc.’...

TECHTRONIC INDUSTRIES NORTH AMERICA, INC. Hwy 8 Pickens, SC 29671 Phone 1-866-340-3912 983000-8683-3-06 (REV:01) • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertin...