Hunter MD506-01 - Manuals

www.hunterfan.com.br Tools Needed Ladder Pliers Wire Strippers Screwdrivers Power Drill (optional) 3.5 mm Drill Bit (optional) 8 mm Drill Bit (optional) If mounting to a support structure, you will also need these tools. Hammer (optional) 3 MD506-01 • 09/19/14 • © Hunter Fan Company

www.hunterfan.com.br Hang your fan by a standard downrod (included) or use a shorter downrod ( sold separately ) for Low-Profile Mounting. Mounting Options Ceiling Bracket Note: Do not hang the fan from a ceiling that is angled greater than 34 ° Support Structure Ceiling Outlet Box (required) Angled...

6 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Assembling the Top Housing KEEP! Remove the pre-installed setscrew so that the downrod can be inserted. KEEP! Install three upper motor cover screws, found in the hardware bag, and tighten them securely. Upper Motor Cover Screw To ass...

7 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Downrod S lide S lide 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Longer Downrod for angled ceilings or ceilings 3 m or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 2,4-3 m high Option 1 Option ...

8 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company 20 cm 1 cm CU T & ST R IP (not to scale) The wires can be cut, but leave at least 20 cm extending from the top of the downrod. Downrod (continued) If the setscrew is not tightened securely, the fan may fall. 20 cm 1 cm Hand tighte...

9 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan.

10 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Wiring Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of t...

11 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Canopy Note: Fan style may vary. Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Insert the two canopy screws fou...

12 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Attach the blade to...

13 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Light Kit Align the keyholes in the light kit with the two partially installed screws and turn the light kit clockwise until the screws are in the narrow ends of the keyholes. Thread the 9-pin plug connector from the fan through the ...

17 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Remote Control Within 3 minutes of restoring power to the fan, press both the Fan Off button and the High button for at least 4 seconds. Your fan will turn on low to indicate successful syncing. If it does not, turn off power to your...

19 www.hunterfan.com.br MD506-01 • 09/19/14 • © Hunter Fan Company Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. Noisy Operation • Tighten t...