Hunter MB517-01 - Manuals

4 MB517-01 • 03/10/15 • © Hunter Fan Company www.HunterFanInternational.com If you have an angled ceiling: 1. You will need a longer downrod (included) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches BOTH Ceiling & Wall ...

www.HunterFanInternational.com Ceiling Bracket OFF Make sure all four (4) bumpers are still attached. For angled ceilings, point opening toward peak. Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers...

www.HunterFanInternational.com Ceiling Bracket (continued) Preparation DISCA RD DI SCARD Remove the shipping blocks from the motor. Discard the screws. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and discard the screws. www.HunterFanInternational.com ...

7 MB517-01 • 03/10/15 • © Hunter Fan Company www.HunterFanInternational.com Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Option 1 Option 2 skip to next page If you need a different downrod length follow these steps: Steps 1-5 to remove standard downrod pipe Steps 6-10 to reassemble with new pipe Stand...

8 MB517-01 • 03/10/15 • © Hunter Fan Company www.HunterFanInternational.com KEEP! Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. Downrod (continued) Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. If th...

www.HunterFanInternational.com Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. 9 MB517-01 • 03/10/15 • © Hunter Fan Company

10 MB517-01 • 03/10/15 • © Hunter Fan Company www.HunterFanInternational.com Wiring Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other...

www.HunterFanInternational.com Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. Screw holes ...

www.HunterFanInternational.com Put the blade washers, found in the hardware bag, onto the blade screws, found in the hardware bag. Then install the blade screws to secure each blade to a blade iron. Blades Lightly attach the blade irons to the motor with screws found in the hardware bag, then secure...

www.HunterFanInternational.com Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. Switch Housing Feed the wire plug through the center hole of the upper switch housing, th...

15 MB517-01 • 03/10/15 • © Hunter Fan Company www.HunterFanInternational.com Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Partially install two of the swi...

www.HunterFanInternational.com Light Kit (continued) Note: In compliance with US federal energy regulations, this ceiling fan contains a device that restricts its light output. Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket(s) may result in fire hazard or i...

www.HunterFanInternational.com Rocker- Style Plate Switch Cover Plate Removed Tabs To install the transmitter cradle, remove the two screws holding the switch cover plate. Do not remove the cover plate. Orient the cradle by lining up the two mounting holes with those on the cover plate. Insert and t...

www.HunterFanInternational.com Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. • Use the provided balancing k it and instructions to balance t...