Hunter M3559-01 - Manuals

Hunter M3559-01 – Manual in PDF format online.

Manuals:

Manual

Manual Hunter M3559-01

Summary

Page 2 - Read and Save These Instructions; WARNINGS; CAUTIONS; What to Expect with Your Installation

www.HunterFan.com 1.888.830.1326 w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box. w.2 - To avoid poss...

Page 3 - Tools Needed; Power Drill

www.HunterFan.com 1.888.830.1326 Tools Needed Power Drill (optional) 9/64” Drill Bit (optional) Ladder Screwdrivers Wire Strippers If mounting to a support structure, you will also need these tools. 3 M3559-01 • 11/12/14 • © Hunter Fan Company

Page 4 - Ceiling Plate; OFF; Turn P; Bumper

www.HunterFan.com 1.888.830.1326 4 M3559-01 • 11/12/14 • © Hunter Fan Company Ceiling Plate Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch locatio...

Page 5 - Top Housing; Trim Ring

www.HunterFan.com 1.888.830.1326 5 M3559-01 • 11/12/14 • © Hunter Fan Company Top Housing Rest the trim ring on the top housing. Trim Ring Thread the wires through the top housing. Place the canopy on the top housing. Ensure all four screw holes line up with the screw holes in both the top housing a...

Page 6 - Grounding; The wires can be cut, but leave at

www.HunterFan.com 1.888.830.1326 Install the top housing screws. Install the grounding screw in the smaller screw hole. These screws can be found in the hardware bag. Grounding Screw Top Housing Screws Top Housing (continued) 8” 3/8” 8” 3/8” CU T & ST R IP (not to scale) The wires can be cut, bu...

Page 7 - Hanging the Fan; Ceiling; To hang the fan, you must tilt the

www.HunterFan.com 1.888.830.1326 Hanging the Fan Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: Fan style may vary. Place the slots over the ceiling plate hooks to hang the fan. Ceiling Plate Hook Ceiling Plate Hook Note: To hang the fan, you must tilt the...

Page 8 - Wiring; To connect the wires,; For Dual Switches

www.HunterFan.com 1.888.830.1326 F R O M FA N Wiring W hit e Black (G rounded) Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. Using the orange wire connectors from the hardware bag, connect the black wire (ungrou...

Page 9 - Canopy; Partially install a canopy screw, found

www.HunterFan.com 1.888.830.1326 9 M3559-01 • 11/12/14 • © Hunter Fan Company Canopy Partially install a canopy screw, found in the hardware bag, between the ceiling plate hooks. When all the holes are properly aligned, securely tighten all three canopy screws. Canopy Screw Hold the canopy up with t...

Page 11 - Blades; Lightly attach the blade irons to the motor with

www.HunterFan.com 1.888.830.1326 Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Lightly attach the blade irons to the motor with the ...

Page 12 - Switch Housing; hole of the upper switch housing, then

www.HunterFan.com 1.888.830.1326 Switch Housing Remove the pre-installed screw and red label from the switch housing. SAVE THE SCREW. Note: The screw was installed for shipping purposes only. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the s...

Page 13 - Switch; Lower Switch

www.HunterFan.com 1.888.830.1326 13 M3559-01 • 11/12/14 • © Hunter Fan Company Switch Housing (continued) Insert the third screw, found in the hardware bag, into place and then tighten all three (3) screws. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored ...

Page 14 - the standoff screws are firmly situated in; Save the screws

www.HunterFan.com 1.888.830.1326 Switch Housing (continued) Align the keyhole slots in the lower switch housing with the stand off screws. Turn the housing counterclockwise until the standoff screws are firmly situated in the narrow end of the keyhole slots. Remove the two pre-installed plate screws...

Page 15 - Light Kit; Lift the cover plate, aligning the screw; Wire Basket

www.HunterFan.com 1.888.830.1326 15 M3559-01 • 11/12/14 • © Hunter Fan Company Light Kit Lift the cover plate, aligning the screw holes with the screw holes in the switch housing. Install the plate screws to secure the cover plate to the switch housing. Align the holes in the wire basket and the hoo...

Page 17 - Cleaning the fan; may damage the finishes.; ON

www.HunterFan.com 1.888.830.1326 Maintenance, Operation, & Cleaning Cleaning the fan - Use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. To switch the direction of air flow, move the reverse switch to the opposite position. Reverse Switch The fan pull c...

Page 18 - Troubleshooting; the specifications on the light; Fan doesn’t work; firmly left or right to ensure that; Excessive wobbling

www.HunterFan.com 1.888.830.1326 Troubleshooting Lights dim when turned on or do not turn on at all. • Make sure the wattage of the light bulbs installed matches the specifications on the light sockets. Fan doesn’t work • Make sure power switch is on. • Push the motor reversing switch firmly left or...