Hunter M3535-01 - Manuals

Hunter M3535-01 – Manual in PDF format online.

Manuals:

Manual

Manual Hunter M3535-01

Summary

Page 2 - What to Expect with Your Installation; qualified electrician.; Read and Save These Instructions; WARNINGS; CAUTIONS; Standard Downrod

www.HunterFan.com 1.888.830.1326 M3535-01 • 06/18/13 • © Hunter Fan Company 1.888.830.1326 1.888.830.1326 What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess locat...

Page 3 - Tools Needed; Ladder

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools. 3 M3535-01 • 06/18/13 • © Hunter Fan Company

Page 4 - TU; Mounting Options; Use; to hang the fan from a; OPTION; SLIDE; PLACE; FOLD; Use; Standard Mounting; or

www.HunterFan.com 1.888.830.1326 4 M3535-01 • 06/18/13 • © Hunter Fan Company 1.866.268.1936 If you have an angled ceiling: 1. You will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches ...

Page 5 - Ceiling Bracket; For angled ceilings, point; OFF; Turn P

www.HunterFan.com 1.888.830.1326 Ceiling Bracket 5 Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. For angled ceilings, point opening tow...

Page 6 - Assembling the Top Housing; Upper Motor; housing sits flat on the adapter.

www.HunterFan.com 1.888.830.1326 Assembling the Top Housing KEEP! Remove the pre-installed setscrew so that the downrod can be inserted. KEEP! Install three upper motor cover screws, found in the hardware bag, and tighten them securely. Upper Motor Cover Screw To assemble the housing to the hanger a...

Page 7 - Downrod; Slid; skip to next page; If you need a different downrod length follow these steps:; Steps 1-5 to remove standard downrod pipe; new; pipe; Option 1

www.HunterFan.com 1.888.830.1326 7 M3535-01 • 06/18/13 • © Hunter Fan Company 1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 skip to next page If you need a different downrod length follow these steps: Steps 1-5 to remove standard downrod pipe Steps 6-10 to reassemble with new pipe www.Hu...

Page 8 - The wires can be cut, but leave at least 8”; DO NOT HAND TIGHTEN.; Hand tighten the downrod (at

www.HunterFan.com 1.888.830.1326 Downrod (continued) 8” 3/8” If the setscrew is not tightened securely, the fan may fall. 1.888.830.1326 www.HunterFan.com 8” 3/8” CU T & ST R IP (not to scale) The wires can be cut, but leave at least 8” extending from the top of the downrod. Tighten the setscrew...

Page 9 - DO NOT PICK THE FAN UP BY THE; Place the downrod

1.888.830.1326 9 M3535-01 • 06/18/13 • © Hunter Fan Company www.HunterFan.com Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan.

Page 10 - Wiring; “common out”) to the white; “neutral in” or

www.HunterFan.com 1.888.830.1326 Wiring Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. Refer to CAUTION c....

Page 11 - Canopy; lifted into place, the canopy fits into; Screw

www.HunterFan.com 1.888.830.1326 11 M3535-01 • 06/18/13 • © Hunter Fan Company Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Insert the two canopy screws found in the hard...

Page 12 - Blades; Attach the blade to the motor using the flat; Holes

www.HunterFan.com 1.888.830.1326 Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Attach the blade to the motor using the flat washers ...

Page 13 - Light Kit; Attachment Screw

www.HunterFan.com 1.888.830.1326 Light Kit Align the keyholes in the light kit with the two partially installed screws and turn the light kit clockwise until the screws are in the narrow ends of the keyholes. Thread the 9-pin plug connector from the fan through the light kit. Attachment Screw Partia...

Page 15 - the fluorescent bulb.

www.HunterFan.com 1.888.830.1326 15 M3535-01 • 06/18/13 • © Hunter Fan Company Light Kit (continued) Connect the 4 pin plug from the ballast to the fluorescent bulb. 4 Pin Plug CONGRATULATIONS! YOU’RE DONE! See next page for fan operation instructions. Glass Globe Trim Ring Globe Assembly Screw Plac...

Page 16 - Remote Control; ON; Within 3 minutes; Fan Off

www.HunterFan.com 1.888.830.1326 Remote Control ON Turn P ow er Note: The remote must be paired before the fan will operate. Within 3 minutes of restoring power to the fan, press both the Fan Off button and the High button for at least 4 seconds. Your fan will turn on low to indicate successful sync...

Page 17 - To switch the direction of air flow,; Reverse

www.HunterFan.com 1.888.830.1326 Rocker- Style Plate Switch Cover Plate Removed Tabs To install the transmitter cradle, remove the two screws holding the switch cover plate. Do not remove the cover plate. Orient the cradle by lining up the two mounting holes with those on the cover plate. Insert and...

Page 18 - When cleaning the fan,; use soft brushes or cloths

www.HunterFan.com 1.888.830.1326 18 M3535-01 • 06/18/13 • © Hunter Fan Company Operation, Maintenance, & Cleaning (continued) When cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. Safe-Exit • Press the Fan Off button for at least thre...

Page 19 - Troubleshooting; Excessive wobbling; Make sure power switch is on.; Remote control of fan is erratic; Install a fresh batter y.

www.HunterFan.com 1.888.830.1326 M3535-01 • 06/18/13 • © Hunter Fan Company 19 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Use the provided balancing k it and instructions to balance the fan. Noisy Operation • Tighten the blade and blade...