Hunter M0099-01 - Manuals

Hunter M0099-01 – Manual in PDF format online.

Manuals:

Manual

Manual Hunter M0099-01

Summary

Page 2 - What to Expect with Your Installation; qualified electrician.; Standard Downrod; Read and Save These Instructions; WARNINGS; CAUTIONS

www.HunterFan.com 1.888.830.1326 M0099-01 • 05/06/14 • © Hunter Fan Company 1.888.830.1326 1.888.830.1326 What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess locat...

Page 3 - Tools Needed; Ladder

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools. 3 M0099-01 • 05/06/14 • © Hunter Fan Company

Page 4 - TU; TU; Mounting Options; Use; Standard Mounting; or; Angled Mounting; to hang the fan from a; OPTION; SLIDE; PLACE; FOLD

www.HunterFan.com 1.888.830.1326 4 M0099-01 • 05/06/14 • © Hunter Fan Company If you have an angled ceiling: 1. You will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches BOTH Ceiling &a...

Page 5 - Ceiling Bracket; For angled ceilings, point; OFF; Turn P

www.HunterFan.com 1.888.830.1326 Ceiling Bracket Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. For angled ceilings, point opening towar...

Page 6 - Preparation; DISCA

www.HunterFan.com 1.888.830.1326 Preparation DISCA RD KEEP! Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and save the screws. Time Saver Tip: G...

Page 7 - Downrod; Slid; Option 1; skip to next page; If you need a different downrod length follow these steps:; Steps 1-5 to remove standard downrod pipe; new; pipe

www.HunterFan.com 1.888.830.1326 7 M0099-01 • 05/06/14 • © Hunter Fan Company Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ hi...

Page 8 - DO NOT

www.HunterFan.com 1.888.830.1326 8 M0099-01 • 05/06/14 • © Hunter Fan Company KEEP! 8” 3/8” CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at l...

Page 9 - DO NOT PICK THE FAN UP BY THE; Place the downrod

www.HunterFan.com 1.888.830.1326 Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. 9 M0099-01 • 05/06/14 • © Hunter Fan Company

Page 10 - Wiring

www.HunterFan.com 1.888.830.1326 Wiring Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. Refer to CAUTION c....

Page 11 - Canopy; lifted into place, the canopy fits into; Screw

www.HunterFan.com 1.888.830.1326 Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardware bag. Note: Fan style may vary...

Page 12 - Blades

www.HunterFan.com 1.888.830.1326 Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. Insert grommets found in the hardware bag into the ho...

Page 13 - Switch Housing

www.HunterFan.com 1.888.830.1326 Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw ho...

Page 14 - Light Kit; Want to install your fan without a light kit?

www.HunterFan.com 1.888.830.1326 14 M0099-01 • 05/06/14 • © Hunter Fan Company Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Align the notches in the sides...

Page 16 - Remote Control; Within 3 minutes; Fan ON; If you are installing multiple remote-controlled fans on; ON

www.HunterFan.com 1.888.830.1326 Remote Control Note: The remote must be paired before the fan will operate. Within 3 minutes of restoring power to the fan, press both the Fan OFF button and the Fan ON button for at least 4 seconds. Your fan will turn on to indicate successful syncing. If it does no...

Page 17 - The lights will flash for visual confirmation.

www.HunterFan.com 1.888.830.1326 17 M0099-01 • 05/06/14 • © Hunter Fan Company Fan Operation: Press and quickly release the ON or OFF button on the remote control to turn the fan OFF or ON. To change the fan speed, slowly pull the fan pull-chain switch to select the desired speed. Light Operation: P...

Page 18 - Changing the bulbs; finial and remove it from the threaded; Changing the direction of air; may damage the finishes.

www.HunterFan.com 1.888.830.1326 Operation, Maintenance, & Cleaning (continued) Changing the bulbs - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand. Carefully remove the globe. Unscrew bul...

Page 19 - Troubleshooting; Excessive wobbling; firmly left or right to ensure that; Remote control of fan is erratic

www.HunterFan.com 1.888.830.1326 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. Noisy Operation • Tighten the blade and blade iron screws unt...