Hunter M0028-01 - Manuals - manualsarea.com

Page 2 - What to Expect with Your Installation; qualified electrician.; Read and Save These Instructions; WARNINGS; CAUTIONS

www.HunterFan.com 1.888.830.1326 M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess location 30 inches from b...

Page 3 - Tools Needed; Ladder

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers If mounting to a support structure, you will also need these tools. 3 M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company

Page 4 - Ceiling Bracket; OFF; Turn P; Make sure all four bumpers are still attached.; Bumper

www.HunterFan.com 1.888.830.1326 4 M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Ceiling Bracket OFF Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wal...

Page 5 - Preparation; Get a helper

www.HunterFan.com 1.888.830.1326 Ceiling Bracket (continued) Preparation 1.888.830.1326 www.HunterFan.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company

Page 6 - Hanging the Fan

www.HunterFan.com 1.888.830.1326 Hanging the Fan While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Ground Wire Note...

Page 7 - Wiring; For Dual Switches

www.HunterFan.com 1.888.830.1326 Wiring F RO M F A N F RO M CE IL ING BR A CK E T F R O M F A N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, fan, and hanging bracket. (G rounding) G reen/Y e...

Page 8 - Motor Housing; The motor housing is

www.HunterFan.com 1.888.830.1326 With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag. Tighten all four screws securely. Motor Housing Screw Holes Motor Housing Screw Indentation Notch Raise the motor housing up over the motor and ceiling bracket. Turn th...

Page 9 - Blades

www.HunterFan.com 1.888.830.1326 Blades Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after...

Page 10 - Switch Housing

www.HunterFan.com 1.888.830.1326 Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw ho...

Page 11 - Light Kit; Want to install your fan without a light kit?

www.HunterFan.com 1.888.830.1326 11 M0028-01 • 06/25/15 • © 2012–2015 Hunter Fan Company Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Partially install tw...

Page 12 - Note: Glass shade style and number of lights may vary.

www.HunterFan.com 1.888.830.1326 Light Kit (continued) CONGRATULATIONS! YOU’RE DONE! Note: Glass shade style and number of lights may vary. See next page for fan operation instructions. Connect the appropriate pull chain pendant to each of the short chains coming from the finial and finial cap. The ...

Page 13 - Cleaning the fan; may damage the finishes.; Changing the bulbs; the finial and remove it from the; Changing the direction of air; ON

www.HunterFan.com 1.888.830.1326 Maintenance, Operation & Cleaning Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. Changing the bulbs - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the gl...

Page 14 - Troubleshooting; Excessive wobbling; Make sure power switch is on.

www.HunterFan.com 1.888.830.1326 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Use the provided balancing k it and instructions to balance the fan. Noisy Operation • Tighten the blade and blade iron screws until they are snug. • Check to s...