Hunter 54015 - Manuals - manualsarea.com

Page 2 - What to Expect with Your Installation; qualified electrician.; Standard Downrod; Read and Save These Instructions; WARNINGS; CAUTIONS

www.HunterFan.com 1.888.830.1326 M0074-01 • 05/14/14 • © Hunter Fan Company 1.888.830.1326 1.888.830.1326 What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess locat...

Page 3 - Tools Needed; Ladder

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools. 3 M0074-01 • 05/14/14 • © Hunter Fan Company

Page 4 - TU; TU; Mounting Options; Use; Standard Mounting; or; Angled Mounting; to hang the fan from a; OPTION; SLIDE; PLACE; FOLD

www.HunterFan.com 1.888.830.1326 4 M0074-01 • 05/14/14 • © Hunter Fan Company 1.866.268.1936 If you have an angled ceiling: 1. You will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches ...

Page 5 - Ceiling Bracket; For angled ceilings, point; OFF; Turn P

www.HunterFan.com 1.888.830.1326 1.888.830.1326 www.HunterFan.com Ceiling Bracket 5 Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. For a...

Page 6 - Preparation; DISCA

www.HunterFan.com 1.888.830.1326 1.888.830.1326 www.HunterFan.com Preparation DISCA RD KEEP! Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. Please remove the ring and s...

Page 7 - Downrod; Slid; Option 1; skip to next page; If you need a different downrod length follow these steps:; Steps 1-5 to remove standard downrod pipe; new; pipe

1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a d...

Page 8 - DO NOT

KEEP! 8” 3/8” CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downrod. Downrod (continued) 8” 3/8” Tig...

Page 9 - DO NOT PICK THE FAN UP BY THE; Place the downrod

1.888.830.1326 9 M0074-01 • 05/14/14 • © Hunter Fan Company www.HunterFan.com Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan.

Page 10 - Wiring

www.HunterFan.com 1.888.830.1326 Wiring Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. Refer to CAUTION c....

Page 11 - Canopy; lifted into place, the canopy fits into; Screw

www.HunterFan.com 1.888.830.1326 11 M0074-01 • 05/14/14 • © Hunter Fan Company Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Screw Holes Insert the two canopy screws found...

Page 12 - Blades

www.HunterFan.com 1.888.830.1326 M0074-01 • 05/14/14 • © Hunter Fan Company Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. 12 Insert ...

Page 13 - Switch Housing

www.HunterFan.com 1.888.830.1326 Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw ho...

Page 15 - Within 3 minutes; ON; Turn Power; If you are installing multiple remote-controlled fans on the same

www.HunterFan.com 1.888.830.1326 Within 3 minutes of restoring power to the fan, press both the Fan Off button and the High button for at least 4 seconds. Your fan will turn on low to indicate successful syncing. If it does not, turn off power to your fan, wait 1 minute then try again. If using the ...

Page 17 - Troubleshooting; Fan doesn’t work; firmly left or right to ensure that it; Excessive wobbling

www.HunterFan.com 1.888.830.1326 M0074-01 • 05/14/14 • © Hunter Fan Company 17 Troubleshooting Fan doesn’t work • Make sure power switch is on. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breake...