Hunter 53250 - Manuals - manualsarea.com

Page 2 - What to Expect with Your Installation; Read and Save These Instructions; WARNINGS; CAUTIONS; Standard Downrod

www.HunterFan.com 1.888.830.1326 M0031-01 • 01/15/13 • © Hunter Fan Company What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess location 30 inches from blade tip t...

Page 3 - Tools Needed

www.HunterFan.com 1.888.830.1326 M0031-01 • 01/15/13 • © Hunter Fan Company Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools. 3

Page 4 - TU; Mounting Options; Standard Mounting; OPTION; OPTION; SLIDE; PLACE; FOLD

www.HunterFan.com 1.888.830.1326 4 M0031-01 • 01/15/13 • © Hunter Fan Company If you have an angled ceiling: 1. You will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches BOTH Ceiling &a...

Page 5 - Ceiling Bracket; OFF; Turn P

1.888.830.1326 www.HunterFan.com Ceiling Bracket OFF For angled ceilings, point opening toward peak. Refer to warning w.1 on pg. 2 If you are unable to do this, call Technical Support at 1-888-830-1326. Use wood screws (included) when securing to support structure with approved electrical outlet box...

Page 6 - Downrod; Slid; Option 1; skip to next page; If you need a different downrod length follow these steps:; Steps 1-5 to remove standard downrod pipe; new; pipe

1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a d...

Page 7 - DO NOT

KEEP! 8” 3/8” CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downrod. Downrod (continued) 8” 3/8” Tig...

Page 8 - DO NOT PICK THE FAN UP BY THE

1.888.830.1326 8 M0031-01 • 01/15/13 • © Hunter Fan Company www.HunterFan.com Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan.

Page 9 - Wiring; For Dual Switches

www.HunterFan.com 1.888.830.1326 Wiring FR O M F A N F RO M C E I LING B RA CK E T F R O M FA N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. (G rounding) G reen...

Page 10 - Canopy; Screw

www.HunterFan.com 1.888.830.1326 10 M0031-01 • 01/15/13 • © Hunter Fan Company Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Screw Holes Insert the two canopy screws found...

Page 11 - Blades

www.HunterFan.com 1.888.830.1326 M0031-01 • 01/15/13 • © Hunter Fan Company Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. 11 Align t...

Page 12 - Light Kit; Want to install your fan without a light kit?

www.HunterFan.com 1.888.830.1326 Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three switch housing screws could result in the light fixture falling. Want to install your fan without a light kit? Go to www.HunterFan.com/...

Page 13 - Note: Globe style and number of lights may vary.

www.HunterFan.com 1.888.830.1326 Light Kit (continued) CONGRATULATIONS! YOU’RE DONE! Note: Globe style and number of lights may vary. See next page for fan operation instructions. Connect the appropriate pull chain pendant to each of the short chains coming from the finial and finial cap. The fan pu...

Page 14 - Maintenance & Cleaning; Changing the direction of air; ON; Cleaning the fan; Changing the bulbs

www.HunterFan.com 1.888.830.1326 M0031-01 • 01/15/13 • © Hunter Fan Company 14 Maintenance & Cleaning Changing the direction of air flow - move the reverse switch to the opposite position. ON Turn P ow er Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may ...

Page 15 - Troubleshooting; Excessive wobbling

M0031-01 • 01/15/13 • © Hunter Fan Company www.HunterFan.com 1.888.830.1326 15 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Use the provided balancing k it and instructions to balance the fan. Noisy Operation • Tighten the blade and blade...