Hunter 53200 - Manuals - manualsarea.com

Page 2 - What to Expect with Your Installation; qualified electrician.; Read and Save These Instructions; WARNINGS; CAUTIONS; Standard Downrod; than 34° will require an

www.HunterFan.com 1.888.830.1326 M3520-01 • 04/19/13 • © Hunter Fan Company 1.888.830.1326 1.888.830.1326 What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess locat...

Page 3 - Tools Needed; Ladder

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools. 3 M3520-01 • 04/19/13 • © Hunter Fan Company

Page 4 - TU; Mounting Options; Use Standard Mounting; to hang the fan from a flat ceiling.; Use Angled Mounting; to hang the fan from a; OPTION; OPTION; SLIDE; PLACE; FOLD

www.HunterFan.com 1.888.830.1326 4 M3520-01 • 04/19/13 • © Hunter Fan Company 1.866.268.1936 If you have an angled ceiling: 1. You will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches ...

Page 5 - Ceiling Bracket; OFF; For angled ceilings, point; If you are unable to do this,; Turn P

1.888.830.1326 www.HunterFan.com Ceiling Bracket OFF Make sure all four (4) bumpers are still attached. For angled ceilings, point opening toward peak. Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breake...

Page 6 - Preparation; DISCA

www.HunterFan.com 1.888.830.1326 Ceiling Bracket (continued) Preparation 1.888.830.1326 www.HunterFan.com DISCA RD KEEP! Remove the shipping blocks from the motor. Save the screws. They will be needed for blade iron installation. Note: Some fans will have a shipping ring instead of shipping blocks. ...

Page 7 - Downrod; Slid; Option 1; skip to next page; If you need a different downrod length follow these steps:; Steps 1-5 to remove standard downrod pipe; Steps 6-10 to reassemble with new pipe

1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a d...

Page 8 - leave at least 8” extending

KEEP! 8” 3/8” CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downrod. Downrod (continued) 8” 3/8” Tig...

Page 9 - DO NOT PICK THE FAN UP BY THE; ball into the slot in the ceiling bracket.

1.888.830.1326 9 M3520-01 • 04/19/13 • © Hunter Fan Company www.HunterFan.com Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan.

Page 10 - Wiring; For Dual Switches

www.HunterFan.com 1.888.830.1326 Wiring FR O M F A N F RO M C E I LING B RA CK E T F R O M FA N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. (G rounding) G reen...

Page 11 - Canopy; lifted into place, the canopy fits into; Screw

www.HunterFan.com 1.888.830.1326 11 M3520-01 • 04/19/13 • © Hunter Fan Company Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Screw Holes Insert the two canopy screws found...

Page 12 - Blades

www.HunterFan.com 1.888.830.1326 M3520-01 • 04/19/13 • © Hunter Fan Company Blades Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. 12 Remembe...

Page 13 - Switch Housing

www.HunterFan.com 1.888.830.1326 Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two scre...

Page 14 - Light Kit; Want to install your fan without a light kit?; “How do I install my fan without the light kit?”

www.HunterFan.com 1.888.830.1326 Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Partially install two of the switch housing screws found in the bag. Connect...

Page 16 - Maintenance & Cleaning; ON; Changing the bulbs - unscrew; the finial and remove it from the; Changing the direction of air; may damage the finishes.

www.HunterFan.com 1.888.830.1326 M3520-01 • 04/19/13 • © Hunter Fan Company 16 Maintenance & Cleaning ON Turn P ow er Changing the bulbs - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand. C...

Page 17 - Troubleshooting; Excessive wobbling; Make sure power switch is on.

www.HunterFan.com 1.888.830.1326 M3520-01 • 04/19/13 • © Hunter Fan Company 17 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. • Use the provi...