Hunter 53074 - Manuals - manualsarea.com

Page 2 - What to Expect with Your Installation; Read and Save These Instructions; WARNINGS; CAUTIONS

www.HunterFan.com 1.888.830.1326 M0047-01 • 11/26/12 • © Hunter Fan Company 1.888.830.1326 1.888.830.1326 What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess locat...

Page 3 - Tools Needed

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers If mounting to a support structure, you will also need these tools. 3 M0047-01 • 11/26/12 • © Hunter Fan Company

Page 4 - Ceiling Bracket; OFF; Turn P; Bumper

1.888.830.1326 www.HunterFan.com Ceiling Bracket OFF Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Turn P ow er 4 Use wood screws (incl...

Page 5 - Preparation

www.HunterFan.com 1.888.830.1326 Ceiling Bracket (continued) Preparation 1.888.830.1326 www.HunterFan.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M0047-01 • 11/26/12 • © Hunter Fan Company

Page 6 - Hanging the Fan

www.HunterFan.com 1.888.830.1326 6 M0047-01 • 11/26/12 • © Hunter Fan Company Hanging the Fan While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large ope...

Page 7 - Wiring

www.HunterFan.com 1.888.830.1326 Wiring Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. Refer to CAUTION c....

Page 8 - Motor Housing

www.HunterFan.com 1.888.830.1326 With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag. Tighten all four screws securely. Motor Housing Screw Holes Motor Housing Screw Indentation Notch Raise the motor housing up over the motor and ceiling bracket. Turn th...

Page 9 - Blades

www.HunterFan.com 1.888.830.1326 M0047-01 • 11/26/12 • © Hunter Fan Company Blades 9 Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in ...

Page 10 - Switch Housing

www.HunterFan.com 1.888.830.1326 Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two scre...

Page 11 - ON

www.HunterFan.com 1.888.830.1326 Switch Housing Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Partially install two of the switch housing screws found in the bag. Co...

Page 13 - Troubleshooting

www.HunterFan.com 1.888.830.1326 M0047-01 • 11/26/12 • © Hunter Fan Company 13 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Use the provided balancing k it and instructions to balance the fan. Noisy Operation • Tighten the blade and blade...