Hunter 53057 - Manuals - manualsarea.com

Page 2 - What to Expect with Your Installation; Read and Save These Instructions; WARNINGS; CAUTIONS

www.HunterFan.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter Fan Company 1.888.830.1326 1.888.830.1326 What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess locat...

Page 3 - Tools Needed

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers If mounting to a support structure, you will also need these tools. 3 M0010-01 • 11/02/12 • © Hunter Fan Company

Page 4 - Ceiling Bracket; OFF; Turn P; Bumper

1.888.830.1326 www.HunterFan.com Ceiling Bracket OFF Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Turn P ow er 4 M0010-01 • 11/02/12 •...

Page 5 - Preparation

www.HunterFan.com 1.888.830.1326 Ceiling Bracket (continued) Preparation 1.888.830.1326 www.HunterFan.com Time Saver Tip: Get a helper to insert grommets, found in the hardware bag, into the blades while you’re doing the next couple of steps. 5 M0010-01 • 11/02/12 • © Hunter Fan Company

Page 6 - Hanging the Fan

www.HunterFan.com 1.888.830.1326 6 M0010-01 • 11/02/12 • © Hunter Fan Company Hanging the Fan While holding the wires out of the way, lift the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large ope...

Page 7 - Wiring; For Dual Switches

www.HunterFan.com 1.888.830.1326 Wiring FR O M F A N F RO M C E I LING B RA CK E T F R O M FA N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. (G rounding) G reen...

Page 8 - Motor Housing; The motor housing is

www.HunterFan.com 1.888.830.1326 With a Phillips head screwdriver, install the four motor housing screws found in the hardware bag. Tighten all four screws securely. Motor Housing Screw Holes Motor Housing Screw Indentation Notch Raise the motor housing up over the motor and ceiling bracket. Turn th...

Page 9 - Blades

www.HunterFan.com 1.888.830.1326 Blades 9 M0010-01 • 11/02/12 • © Hunter Fan Company Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardware bag. Lightly attach the blade irons to the motor with screws found in ...

Page 10 - Switch Housing

www.HunterFan.com 1.888.830.1326 Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two scre...

Page 11 - Light Kit; Switch; Want to install your fan without a light kit?

www.HunterFan.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the hardware bag. Align the notches in the sides of the lower switch housing with the ...

Page 13 - ON

www.HunterFan.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter Fan Company 13 Maintenance, Operation & Cleaning The fan pull chain controls the speed: high, medium, low, and off. The light pull chain controls the light fixture: on and off. To switch the direction of air flow, move the reverse s...

Page 14 - Troubleshooting; Excessive wobbling

www.HunterFan.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter Fan Company 14 Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Use the provided balancing k it and instructions to balance the fan. Noisy Operation • Tighten the blade and blade...