Hunter 45062-01 - Manuals - manualsarea.com

Page 2 - Your new Hunter; Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; • To avoid possible electrical shock, before installing your fan,; Welc om e

2 45062-01 • 07/01/09 • Hunter Fan Company Table Of Contents 1 • Getting Ready . . . . . . . . . . . . . . . . . . . . . . 4 2 • Installing the Hanger Bracket . . . . . . . 5 3 • Assembling and Hanging the Fan . . . 6 4 • Setting the Remote Transmitter and Receiver . . . . . . . . . . . . . . . . . ...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Understanding Mounting and Installer’s Choice; To reduce the risk of personal

3 45062-01 • 07/01/09 • Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s Understanding Mounting and Installer’s Choice ® Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depen...

Page 4 - To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; • Gettin g R eady

4 45062-01 • 07/01/09 • Hunter Fan Company To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need help installing the f...

Page 5 - ANGLED; OR; • Inst al lin g th e Han ger Bracket

5 45062-01 • 07/01/09 • Hunter Fan Company 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” in diameter. Note: Your fan comes with four pre-installed neoprene noise isolators. 2-2. Thread the lead wires from the...

Page 6 - • Setting the Remote Transmitter and Receiver.; • A ssemblin g and Han g in g th e Fan

6 45062-01 • 07/01/09 • Hunter Fan Company You can assemble your fan for standard or angled mounting as shown in steps 3-1 – 3-3. 3-1. To assemble fan to hang down from a flat or angled ceiling, insert the downrod through the canopy, adapter cover grommet, adapter cover, and canopy trim ring. (The a...

Page 7 - • Settin g th e R emot e Transmitt er and R e ceiver

7 45062-01 • 07/01/09 • Hunter Fan Company CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment.Operation is subject to the following two conditions: 1. Thi...

Page 8 - • Wirin g th e Fan

8 45062-01 • 07/01/09 • Hunter Fan Company 5-1. Before attempting installation, make sure the power is still off.5-2. To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. For all these connections use the wire connectors pro...

Page 9 - • Inst al lin g th e C anopy and C anopy Trim Rin g

9 45062-01 • 07/01/09 • Hunter Fan Company 6-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. 6-2. Raise the canopy over the hanger bracket. Align partially installed screws with key slots in canopy. 6-3. Twist canopy clockwise to secure.6-4. Install third & fou...

Page 10 - • Completin g Your Inst al l ation With a Li g ht Fi xture

10 45062-01 • 07/01/09 • Hunter Fan Company Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the light kit top housing, partially install two housing assembly screws into the light kit mounting plate. 7-...

Page 11 - Installing the Bowl; • Completin g Your Inst al l ation With a Li g ht Fi xture (Continu ed)

11 45062-01 • 07/01/09 • Hunter Fan Company Installing the Bowl 7-5. Install 1 Max 40 Watt Circline bulb (included) into spring clamps. 7-6. Connect the cicline bulb.7-7. Lift the globe up to the light kit top housing. Align the three bolts on the globe with the three slots in the light kit top hous...

Page 12 - • O p eratin g th e R emot e Control and Mountin g th e Hol der

12 45062-01 • 07/01/09 • Hunter Fan Company 8-1. The remote has individual buttons for setting fan speed and light intensity. Refer to the figure on the right. Note: For best operation, start the fan by pressing high, then select your desired speed. 8-2. The light button turns the light. Push the li...

Page 13 - -4. Clean wood finish blades with a furniture polishing cloth.; • O p eratin g and Cleanin g Your C ei lin g Fan

13 45062-01 • 07/01/09 • Hunter Fan Company 9-1. Turn on electrical power to the fan.9-2. The remote controls power to the fan. The fan has four settings in sequence: High, Medium, Low and Off. 9-3. For cleaning finishes, use a soft brush or lint-free cloth to prevent scratching. A vacuum cleaner br...

Page 14 - Problem: Lights dim when turned on or do not turn on; Check to make sure the wattage and type of light bulbs installed; 0 • Trouble sho otin g

14 45062-01 • 07/01/09 • Hunter Fan Company Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker.2. Loosen canopy, check all connections according to the wiring the fan section. Problem: Noisy operation. 1. Check to see if the blade is cracked. If so, replace...