Hunter 45037-01 - Manuals - manualsarea.com

Page 2 - Your new Hunter; Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; • To avoid possible electrical shock, before installing your fan,; Welc om e

2 45037-01 • 11/21/08 • Hunter Fan Company Table Of Contents 1 • Getting Ready . . . . . . . . . . . . . . . . . . . . . . 4 2 • Installing the Hanger Bracket . . . . . . . 5 3 • Assembling and Hanging the Fan . . . 6 4 •Wiring the Fan . . . . . . . . . . . . . . . . . . . . . . 8 5 • Installing the...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Understanding Mounting and Installer’s Choice; To

3 45037-01 • 11/21/08 • Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s Understanding Mounting and Installer’s Choice ® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, dep...

Page 4 - To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?; • Gettin g R eady

4 45037-01 • 11/21/08 • Hunter Fan Company To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need help installing the f...

Page 5 - ANGLED; OR; • Inst al lin g th e Han ger Bracket

5 45037-01 • 11/21/08 • Hunter Fan Company 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” in diameter. Note: Your fan comes with four pre-installed neoprene noise isolators. 2-2. Thread the lead wires from the...

Page 6 - • A ssemblin g and Han g in g th e Fan

6 45037-01 • 11/21/08 • Hunter Fan Company You can assemble your fan for standard or angled mounting as shown in steps 3-1 – 3-3. For low profile mounting (ceilings less than 8 feet high), go to steps 3-6 – 3-9 on the next page. 3-1. To assemble fan to hang down from a flat or angled ceiling, place ...

Page 7 - • A ssemblin g and Han g in g th e Fan (Low Prof i le O nly); standard

7 45037-01 • 11/21/08 • Hunter Fan Company 3 • A ssemblin g and Han g in g th e Fan (Low Prof i le O nly) You can assemble your fan for standard or angled mounting as shown in steps 3-1 – 3-3 on the previous page. For low profile mounting (ceilings less than 8 feet high), see steps 3-6 – 3-10 on thi...

Page 8 - •Wirin g th e Fan

8 45037-01 • 11/21/08 • Hunter Fan Company All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national a...

Page 9 - • Inst al lin g th e C anopy and C anopy Trim Rin g

9 45037-01 • 11/21/08 • Hunter Fan Company 5-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. 5-2. Raise the canopy over the hanger bracket. Align partially installed screws with key slots in canopy. 5-3. Twist canopy clockwise to secure.5-4. Install third & fou...

Page 10 - • A ssemblin g th e Bl ade s

10 45037-01 • 11/21/08 • Hunter Fan Company Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan).6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using t...

Page 11 - • Inst al lin g th e Sw itch Housin g

11 45037-01 • 11/21/08 • Hunter Fan Company 7-1. To attach the upper switch housing, partially install two housing assembly screws into the switch housing mounting plate. 7-2. Feed the upper plug connector through the center opening of the housing. 7-3. Align the keyhole slots in the housing with th...

Page 12 - • Completin g Your Inst al l ation With a Li g ht Fi xture

12 45037-01 • 11/21/08 • Hunter Fan Company 7-5. To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. Note: Both plug connectors are polarized and will only fit together one way. Make sure the connectors...

Page 13 - • The chain uses a breakaway connector that separates if the; • O p eratin g and Cleanin g Your C ei lin g Fan

13 45037-01 • 11/21/08 • Hunter Fan Company In warm weather , use downward air flow pattern In cold weather , use upward air flow pattern 8-1. Turn on electrical power to the fan.8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low, and O...

Page 14 - Problem: Lights dim when turned on or do not turn on; Check to make sure the wattage and type of light bulbs installed; • Trouble sho otin g

14 45037-01 • 11/21/08 • Hunter Fan Company Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker.2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing.4. Push motor reversing switch...