Hunter 45007 - Manuals - manualsarea.com

Page 2 - ceiling fan is an addition to your home or office that; Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; qualified electrician.; Welc om e; Table Of Contents

2 45007-01 • 11/02/07 • Hunter Fan Company © 2007 Hunter Fan Company Your new Hunter ® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your ...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Understanding Mounting and Installer’s Choice; performance of your Hunter fan, use only Hunter speed controls.; Standard Mounting; To reduce the risk of personal

3 45007-01 • 11/02/07 • Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s Understanding Mounting and Installer’s Choice ® Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depen...

Page 4 - Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?; • Gettin g R eady

4 45007-01 • 11/02/07 • Hunter Fan Company To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need help installing the f...

Page 5 - -2. Thread the lead wires from the outlet box down through the hole; ANGLED; -4. Place a flat washer on each of the two 3” screws and pass the; OR; LEFT; • Inst al lin g th e Han ger Bracket

5 45007-01 • 11/02/07 • Hunter Fan Company 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” in diameter. Note: Your fan comes with four pre-installed neoprene noise isolators. 2-2. Thread the lead wires from the...

Page 6 - Go to; • Wiring the Fan; Fan may fall if not assembled as directed in these; • A ssemblin g and Han g in g th e Fan

6 45007-01 • 11/02/07 • Hunter Fan Company 3-1. To assemble fan to hang down from a flat or angled ceiling, place the canopy and canopy trim ring around the adapter so that they rest on the fan assembly. 3-2. Feed the wires from the fan through the downrod. Note: Make sure all the wires are on the s...

Page 7 - Before you change the DIP switch settings, make; Setting DIP switches; Example DIP Switch Settings; • Settin g th e R emot e Transmitt er and R e ceiver

7 45007-01 • 11/02/07 • Hunter Fan Company 4 • Settin g th e R emot e Transmitt er and R e ceiver CAUTION: The remote control device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Oper...

Page 8 - Be sure no bare wire or wire strands are visible after; • Wirin g th e Fan

8 45007-01 • 11/02/07 • Hunter Fan Company All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. 5-1. Make sure the power is still off. 5-2. Position the receiver in the canopy so that the antenna i...

Page 9 - • Inst al lin g th e C anopy and C anopy Trim Rin g

9 45007-01 • 11/02/07 • Hunter Fan Company 6-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. 6-2. Raise the canopy over the hanger bracket. Align partially installed screws with key slots in canopy. 6-3. Twist canopy clockwise to secure.6-4. Install third & fou...

Page 10 - • A ssemblin g th e Bl ade s

10 45007-01 • 11/02/07 • Hunter Fan Company 7-1. Insert each blade into slot. Align the holes on the blade with the holes on the blade ring. 7-2. Attach the blade to the blade ring using the blade assembly screws. 7-3. Repeat for each blade. Step 7-1 Step 7-2 7 • A ssemblin g th e Bl ade s

Page 11 - Your Hunter fan comes with an integrated light fixture assembly.; Use only the light fixture supplied with this fan model.; assembly screws into the switch housing mounting plate.; Make sure the heat shield assembly is securely; • Completin g Your Inst al l ation With a Bow l Li g ht Fi xture

11 45007-01 • 11/02/07 • Hunter Fan Company Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. 8-1. To attach the heat shield assembly, partially install two housing assembly screws into the switch housing mounting plate...

Page 12 - -6. Align the keyholes in the light kit assembly with the two

12 45007-01 • 11/02/07 • Hunter Fan Company Heat Shield Assembly Light Kit Assembly Steps 8-5 – 8-7 8-5. To attach the light kit, connect the upper plug connector from the heat shield assembly to the lower plug connector in the light kit assembly. Note: Both plug connectors are polarized and will on...

Page 13 - intensity. Refer to the figure on the right.; • O p eratin g th e R emot e Control and Mountin g th e Hol der

13 45007-01 • 11/02/07 • Hunter Fan Company 9 • O p eratin g th e R emot e Control and Mountin g th e Hol der 9-1. The remote has individual buttons for setting fan speed and light intensity. Refer to the figure on the right. Note: For best operation, start the fan by pressing high, then select your...

Page 14 - In warm weather; In cold weather; 0-2. Ceiling fans work best by blowing air downward; To Change Airflow Direction; 0 • O p eratin g and Cleanin g Your C ei lin g Fan

14 45007-01 • 11/02/07 • Hunter Fan Company In warm weather , use downward air flow pattern In cold weather , use upward air flow pattern 10-1. Turn on electrical power to the fan. 10-2. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room...

Page 15 - Loosen canopy, check all connections according to the wiring the; 1 • Trouble sho otin g

15 45007-01 • 11/02/07 • Hunter Fan Company Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing.4. Push motor reversing switc...