Hunter 43545-01 - Manuals - manualsarea.com

Page 2 - Table Of Contents; Your new Hunter; Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; Hunter® fan types A through Z.; Welc om e

2 43545-01 • 05/14/09 • Hunter Fan Company Table Of Contents 1 • Installing the Light Kit on a Removable Switch Housing . . . . . . . . . . . . . . . . . . . 4 2 • Installing the Light Kit on a Non- Removable Switch Housing . . . . . . . . 6 3 • Installing the Light Kit on the Hunter Original . . . ...

Page 3 - Inst al l ation Metho d s of Hunt er® C ei lin g Fans Ty p e A-Z; Removable Switch Housing; Preparing the Light Kit:

3 43545-01 • 05/14/09 • Hunter Fan Company Inst al l ation Metho d s of Hunt er® C ei lin g Fans Ty p e A-Z Removable Switch Housing Non-removable Switch Housing The Hunter Original Preparing the Light Kit: 1. Disconnect power by turning off the circuit breakers both to the outlet box and to its ass...

Page 4 - • Inst al lin g th e Li g ht Kit on Fans With R emovable Sw itch Housin g s

4 43545-01 • 05/14/09 • Hunter Fan Company 1. Unscrew the three screws from the upper switch housing. Disconnect the 9-pin plug connectors. Remove the lower switch housing. 2. Push the plug button from inside the lower switch housing to remove the plug button and switch housing cap. NOTE: Save the p...

Page 5 - : Be sure no bare metal wires or wire strands are visible after; Go to the instructions for installing the bulbs and globe.

5 43545-01 • 05/14/09 • Hunter Fan Company 1 • Inst al lin g th e Li g ht Kit on Fans With R emovable Sw itch Housin g s (Continu ed) 7. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or “For Light Use.” To connect the wires, hold the bare metal lead...

Page 6 - CAUTION; : Be sure no bare metal; Non-Removable Switch

6 43545-01 • 05/14/09 • Hunter Fan Company 1. Uninstall the two attachment screws from the switch housing cover.2. Remove the plug or screw from the center of the switch housing cover.3. Ensure the gasket is in place on the light kit mounting plate. Thread the switch housing cover onto the wires fro...

Page 8 - Uninstall the two screws from the switch housing plate.; NOTE; : Save the switch housing cap should you choose to remove the light; WARNING; : Improper installation; • Inst al lin g th e Li g ht Kit on th e Hunt er O ri g inal

8 43545-01 • 05/14/09 • Hunter Fan Company 1. Uninstall the two screws from the switch housing plate. NOTE : Save the switch housing cap should you choose to remove the light fixture in the future. 2. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or...

Page 9 - • Inst al lin g th e Bul bs, Chain, and Glob e

9 43545-01 • 05/14/09 • Hunter Fan Company CFL Bulb (included) 1. First, install the included CFL medium-based bulbs.2. Loosen the three thumbscrews on the lower edge of the light kit. Raise the glass globe into the light kit. Thread the pull chain through the hole in the center of the globe. Tighte...

Page 10 - Light does not come on.; your ceiling fan manual for locating assembly and wiring.; This Light Fixture Weighs 6 lbs.; • Trouble sho otin g

10 43545-01 • 05/14/09 • Hunter Fan Company Light does not come on. 1. Make sure bulbs are installed properly.2. Make sure breakers or fuses are on.3. Verify that the light power lead is connected at the ceiling. Refer to your ceiling fan manual for locating assembly and wiring. Glass rattles. 1. Ma...