Hunter 43045 - Manuals - manualsarea.com

Page 2 - from the tub or shower opening. See Figure A.; W A R N I N G; Continued; Figure A

43045-01 10/15/2009 2 1) Read all instructions before attempting to install or use this appliance. This appliance is for general ventilating use only. Do not use this appliance for ventilating hazardous or explosive materials. Follow the heating equipment manufacturer’s guideline and safety standard...

Page 4 - Before Installation

43045-01 10/15/2009 4 F G I L M x2 N x6 * * A B C 98141-01-000 03242-07-133 98142-01-000 x2 D 97134-01-000 74508-03-133 Housing Wiring Cover Fan Assembly 3/8” Cable Connector Light Fixture Wiring Cover Screw Check all the parts. If damaged, call 1-888-830-1326 for replacement. x4 E Mounting Screws F...

Page 5 - Choose Installation Option

43045-01 10/15/2009 5 Loosen the wiring cover screw. Remove the fan assembly from the housing. Remove the wiring cover. D E C Choose Installation Option For New Construction - attaching to joist, go to step A1, page 5. For New Construction - suspended between, joists go to step B1, page 7. For Exist...

Page 6 - New Construction - attaching to joist; OR

43045-01 10/15/2009 6 A1 Section A - New Construction - attaching to joist Drive mounting screws (supplied) into joist or framing. Position the correct depth mark at the bottom edge of the joist based upon the the thickness of your sheetrock. 5/81/2 5/81/2 A2 Pop out a wiring access slug. OR Install...

Page 7 - Section B - New Construction – suspended between joists

43045-01 10/15/2009 7 A6 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely, an adapter may need to be purchased. Vaya a la sección E – Instalación Final en la página 14. Section B - New Construction – suspended between joists Pop out a wiring a...

Page 9 - Section C - Existing Construction – accessible from above; NO EXISTING FAN

43045-01 10/15/2009 9 B10 Install the wiring and the strain relief into the wiring access hole you made earlier. B11 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely, an adapter may need to be purchased. Vaya a la sección E – Instalación Final...

Page 12 - Section D - Existing Construction – accessible from below; EXISTING FAN

43045-01 10/15/2009 12 Vaya a la sección E – Instalación Final en la página 14. Section D - Existing Construction – accessible from below Remove one of the wiring access slugs on the top of the housing. Use a second wiring access plug if needed. EXISTING FAN D3 Remove an existing fan and check to ma...

Page 14 - Section E - Final Installation

43045-01 10/15/2009 14 E2 E3 Connect fan wiring harness. DO NOT ALLOW THE FAN TO HANG FROM THE WIRING HARNESS. INSTALLATION IS EASIER IF TWO PEOPLE ARE INVOLVED. Install the wiring cover box. Make sure all wiring connec- tions are inside the wiring cover box. Section E - Final Installation NOTE: Tho...

Page 17 - Preventative Maintenance

43045-01 10/15/2009 17 Trouble Shooting Problem: Fan does not come on. Solution: • Turn power on, replace fuse, or reset breaker. • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Check all plug connectio...

Page 18 - Warranty

43045-01 10/15/2009 18 Hunter Fan Company Bath Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter Bath Fan: If any part of your Hunter Bath Fan fails at any time within one year after the date of sale to you due to a...