Hunter 42678-01 - Manuals - manualsarea.com

Page 2 - Your new Hunter; Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; • To avoid possible electrical shock, before installing your fan,; Welc om e

2 42678-01 • 06/08/09 • Hunter Fan Company Table Of Contents 1 • Getting Ready . . . . . . . . . . . . . . . . . . . . . . 4 2 • Installing the Ceiling Plate . . . . . . . . . . 5 3 • Assembling and Hanging the Fan . . . 6 4 • Wiring the Fan . . . . . . . . . . . . . . . . . . . . . 7 5 • Installing...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Understanding Mounting and Installer’s Choice; To

3 42678-01 • 06/08/09 • Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s Understanding Mounting and Installer’s Choice ® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, dep...

Page 4 - To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?; • Gettin g R eady

4 42678-01 • 06/08/09 • Hunter Fan Company To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need help installing the f...

Page 5 - • Inst al lin g th e C ei lin g Pl at e

5 42678-01 • 06/08/09 • Hunter Fan Company CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fa...

Page 6 - For Standard or Angled mounting:; -2. Insert the downrod through the canopy and canopy trim ring.; For low profile mounting, the downrod is replaced with the; • A ssemblin g and Han g in g th e Fan

6 42678-01 • 06/08/09 • Hunter Fan Company WARNING: Fan may fall if not assembled as directed in these installation instructions. 3-1. Unbundle the wires from the fan. For Standard or Angled mounting: 3-2. Insert the downrod through the canopy and canopy trim ring. Feed the wires from the fan throug...

Page 7 - • Wirin g th e Fan

7 42678-01 • 06/08/09 • Hunter Fan Company fsdfsdf All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with na...

Page 8 - • Inst al lin g th e C anopy and C anopy Trim Rin g

8 42678-01 • 06/08/09 • Hunter Fan Company WARNING: Failure to complete the following steps could cause the fan to fall. Note: It is recommended you use a magnetic tip screwdriver for the following steps. 5-1. Rotate the hanger ball so the tab in the canopy is secure in the hanger ball groove. Note:...

Page 9 - • A ssemblin g th e Bl ade s

9 42678-01 • 06/08/09 • Hunter Fan Company Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan).6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each blade to a blade iron using th...

Page 10 - -2. Feed the upper plug connector through the center opening of the; -5. To attach the lower switch housing, connect the upper plug; • Inst al lin g th e Li g ht Kit

10 42678-01 • 06/08/09 • Hunter Fan Company WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the upper switch housing, partially install two #6-32 x 3/8” housing assembly screws into the switch housing mounting plate. 7-2. Feed the upper plug connector through the cen...

Page 11 - • Inst al lin g th e Li g ht Kit (c ontinu ed); Remove the protective wrap

11 42678-01 • 06/08/09 • Hunter Fan Company 7-7. Remove the plastic from each of the shades.7-8. Install the shades. 7-9. Install the three 60-Watt candelabra light bulbs (included). Steps 7-8 – 7-9 Shade Light Bulb 7 • Inst al lin g th e Li g ht Kit (c ontinu ed) Remove the protective wrap from the...

Page 12 - • The chain uses a breakaway connector that separates if the; • O p eratin g and Cleanin g Your C ei lin g Fan

12 42678-01 • 06/08/09 • Hunter Fan Company In warm weather , use downward air flow pattern In cold weather , use upward air flow pattern 8-1. Turn on electrical power to the fan.8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low, and O...

Page 13 - Problem: Lights dim when turned on or do not turn on; Check to make sure the wattage and type of light bulbs installed; • Trouble sho otin g

13 42678-01 • 06/08/09 • Hunter Fan Company Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker.2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing.4. Push motor reversing switch...