Hunter 42641-01 - Manuals - manualsarea.com

Page 2 - Table of Contents; Welc om e; Your new Hunter; Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; • To avoid possible electrical shock, before installing your fan,

2 Hunter Fan Company 42641-01 • 09/13/07 Table of Contents 1 • Getting Ready ................................................... 4 2 • Installing the Ceiling Plate .......................... 5 3 • Assembling the Fan ....................................... 6 4 • Hanging and Wiring the Fan ..............

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Low Profile Mounting; Standard Mounting; Angled Mounting; Understanding Mounting and Installer’s Choice

3 42641-01 • 09/13/07 Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s Low Profile Mounting fits close to the ceiling, recommended for ceilings less than 8 feet high Standard Mounting hangs from the ceiling by a downrod (included), recommended for ceilings 8 feet or higher Angle...

Page 4 - • Gettin g R eady; To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?

4 Hunter Fan Company 42641-01 • 09/13/07 1 • Gettin g R eady To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need hel...

Page 5 - • Inst al lin g th e C ei lin g Pl at e; To avoid possible electrical shock, before installing your fan,

5 42641-01 • 09/13/07 Hunter Fan Company 2 • Inst al lin g th e C ei lin g Pl at e CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit b...

Page 6 - • A ssemblin g th e Fan; Fan may fall if not assembled as directed in these; For Standard or Angled mounting:; -2. Insert the downrod through the canopy and canopy trim ring.; The adapter has a special coating on the threads. Do; For low profile mounting, the downrod is replaced with the; • Hanging and Wiring the Fan; Standard or Angled Mounting

6 Hunter Fan Company 42641-01 • 09/13/07 3 • A ssemblin g th e Fan Steps 3-2 – 3-3 Low Profile Washer Downrod Canopy Set Screw Low Profile Screw WARNING: Fan may fall if not assembled as directed in these installation instructions. 3-1. Unbundle the wires from the fan. For Standard or Angled mountin...

Page 7 - • Han g in g and Wirin g th e Fan; Single Switch Wiring; Single Switch Wiring:; Be sure no bare wire or wire strands are visible after making

7 42641-01 • 09/13/07 Hunter Fan Company 4 • Han g in g and Wirin g th e Fan Single Switch Wiring Dual Switch Wiring Wire connector 4-1. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position...

Page 8 - • Inst al lin g th e C anopy and C anopy Trim Rin g; Failure to complete the following steps could cause the fan

8 Hunter Fan Company 42641-01 • 09/13/07 5 • Inst al lin g th e C anopy and C anopy Trim Rin g WARNING: Failure to complete the following steps could cause the fan to fall. Note: It is recommended you use a magnetic tip screwdriver for the following steps. 5-1. Rotate the hanger ball so the tab in t...

Page 9 - • A ssemblin g th e Bl ade s; insert them by hand into the holes on the blades.

9 42641-01 • 09/13/07 Hunter Fan Company 6 • A ssemblin g th e Bl ade s Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan).6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each b...

Page 10 - • Completin g Your Inst al l ation w ith a Li g ht Fi xture; Your Hunter fan comes with an integrated light fixture assembly.; Use only the light fixture supplied with this fan model.; -2. Feed the upper plug connector through the center opening of the; Make sure the upper switch housing is securely

10 Hunter Fan Company 42641-01 • 09/13/07 7 • Completin g Your Inst al l ation w ith a Li g ht Fi xture Steps 7-1 – 7-3 Housing Assembly Screw Upper Switch Housing Step 7-4 Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan mod...

Page 11 - -5. To attach the lower switch housing, connect the upper plug

11 42641-01 • 09/13/07 Hunter Fan Company 7-5. To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. Note: Both plug connectors are polarized and will only fit together one way. Make sure the connectors a...

Page 12 - • O p eratin g and Cleanin g Your C ei lin g Fan; In warm weather; In cold weather; To Change Airflow Direction; • The chain uses a breakaway connector that separates if the

12 Hunter Fan Company 42641-01 • 09/13/07 8 • O p eratin g and Cleanin g Your C ei lin g Fan In warm weather , use downward air flow pattern In cold weather , use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to a complete stop. Slide the reversing switch on th...

Page 13 - • Trouble sho otin g; plate and in the upper and lower switch housing.

13 42641-01 • 09/13/07 Hunter Fan Company 9 • Trouble sho otin g Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker.2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing.4. Push m...