Hunter 42609-01 - Manuals - manualsarea.com

Page 2 - Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; • To avoid possible electrical shock, before installing your fan,; Welc om e; Table of Contents

2 42687-01 • 09/08/09 • Hunter Fan Company © 2009 Hunter Fan Company Your new Hunter ® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your ...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Low Profile Mounting; Standard Mounting; Angle Mounting; Understanding Mounting and Installer’s Choice

3 42687-01 • 09/08/09 • Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s Low Profile Mounting fits close to the ceiling, recommended for ceilings less than 8 feet high Standard Mounting hangs from the ceiling by a downrod (included), recommended for ceilings 8 feet or higher Ang...

Page 4 - • Gettin g R eady; To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?

4 42687-01 • 09/08/09 • Hunter Fan Company 1 • Gettin g R eady To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need h...

Page 5 - • Inst al lin g th e C ei lin g Pl at e; To avoid possible electrical shock, before installing your fan,; For Angled Ceilings:

5 42687-01 • 09/08/09 • Hunter Fan Company 2 • Inst al lin g th e C ei lin g Pl at e CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit...

Page 6 - • A ssemblin g th e Fan; Fan may fall if not assembled as directed in these; For Standard or Angle mounting:; The adapter has a special coating on the threads. Do; • Hanging and Wiring the Fan; Standard or Angle Mounting

6 42687-01 • 09/08/09 • Hunter Fan Company 3 • A ssemblin g th e Fan Steps 3-2 – 3-3 Low Profile Washer Downrod Canopy Set Screw Low Profile Screw WARNING: Fan may fall if not assembled as directed in these installation instructions. 3-1. Unbundle the wires from the fan. For Standard or Angle mounti...

Page 7 - • Han g in g and Wirin g th e Fan; Be sure no bare wire or wire strands are visible after; Single Switch Wiring:; Single Switch Wiring

7 42687-01 • 09/08/09 • Hunter Fan Company 4 • Han g in g and Wirin g th e Fan 4-1. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate ho...

Page 8 - • Inst al lin g th e C anopy and C anopy Trim Rin g; Failure to complete the following steps could cause the fan

8 42687-01 • 09/08/09 • Hunter Fan Company 5 • Inst al lin g th e C anopy and C anopy Trim Rin g WARNING: Failure to complete the following steps could cause the fan to fall. Note: It is recommended you use a magnetic tip screwdriver for the following steps. 5-1. Rotate the hanger ball so the tab in...

Page 9 - • A ssemblin g th e Bl ade s; insert them by hand into the holes on the blades.

9 42687-01 • 09/08/09 • Hunter Fan Company 6 • A ssemblin g th e Bl ade s Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan).6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 6-2. Attach each...

Page 10 - • Completin g Your Inst al l ation With or Without a Li g ht Fi xture; -2. Feed the upper plug connector through the center opening of the; Make sure the upper switch housing is securely; If you want to install the light fixture; , you need to uninstall it; Use only the light fixture supplied with this fan model.; In compliance with US federal energy regulations this

10 42687-01 • 09/08/09 • Hunter Fan Company Steps 7-1 – 7-3 Housing Assembly Screw 7 • Completin g Your Inst al l ation With or Without a Li g ht Fi xture Upper Switch Housing 7-1. To attach the upper switch housing, partially install two #6-32 x 3/8” housing assembly screws into the switch housing ...

Page 11 - Note: If you do not want to install the light fixture; “Uninstalling the Light Fixture” on page 12.; Installing the Shades and Bulbs

11 42687-01 • 09/08/09 • Hunter Fan Company Note: If you do not want to install the light fixture , see “Uninstalling the Light Fixture” on page 12. 7-5. To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assemb...

Page 12 - Uninstalling the Light Fixture; Loosen and remove the three screws that attach the light kit

12 42687-01 • 09/08/09 • Hunter Fan Company Uninstalling the Light Fixture 1. Loosen and remove the three screws that attach the light kit to the light kit mounting plate. 2. Uninstall the nut inside the lower switch housing.3. Disconnect the plug connectors between the black wire and the black/whit...

Page 13 - • O p eratin g and Cleanin g Your C ei lin g Fan; • The chain uses a breakaway connector that separates if the; In warm weather; In cold weather; To Change Airflow Direction

13 42687-01 • 09/08/09 • Hunter Fan Company 8 • O p eratin g and Cleanin g Your C ei lin g Fan 8-1. Turn on electrical power to the fan.8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settin...

Page 14 - • Trouble sho otin g; Problem: Lights dim when turned on or do not turn on

14 42687-01 • 09/08/09 • Hunter Fan Company 9 • Trouble sho otin g Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker.2. Loosen canopy, check all connections according to the wiring the fan section.3. Check the plug connection in the switch housing.4. Push ...