Hunter 20731 - Manuals - manualsarea.com

Page 2 - Cautions and Warnings; READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING; • To avoid possible electrical shock, before installing your fan,; Welc om e

2 45034-01 • 10/23/08 • Hunter Fan Company © 2008 Hunter Fan Company Your new Hunter ® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your ...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Understanding Mounting and Installer’s Choice; To

3 45034-01 • 10/23/08 • Hunter Fan Company Inst al ler’s Choice and O ptional Ac ce ss orie s Understanding Mounting and Installer’s Choice ® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, dep...

Page 4 - To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?; • Gettin g R eady

4 45034-01 • 10/23/08 • Hunter Fan Company To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need help installing the f...

Page 5 - ANGLED; OR; • Inst al lin g th e Han ger Bracket

5 45034-01 • 10/23/08 • Hunter Fan Company 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” in diameter. Note: Your fan comes with four pre-installed neoprene noise isolators. 2-2. Thread the lead wires from the...

Page 6 - • Inst al lin g th e Bl ade s

6 45034-01 • 10/23/08 • Hunter Fan Company 3-1. Attach each blade to a blade iron using five blade washers and five blade assembly screws. Blade Assembly Screw Blade Washers Blade Assembly Screws Step 3-1 3 • Inst al lin g th e Bl ade s

Page 7 - • Wiring the Fan; • A ssemblin g and Han g in g th e Fan

7 45034-01 • 10/23/08 • Hunter Fan Company You can assemble your fan for standard or angled mounting as shown in steps 4-1 – 4-6. For low profile mounting (ceilings less than 8 feet high), go to steps 4-7 – 4-11 on the next page. 4-1. Unbundle the wires from the fan and remove the paper caution tag....

Page 8 - • A ssemblin g and Han g in g th e Fan (Low Prof i le O nly); standard

8 45034-01 • 10/23/08 • Hunter Fan Company 4 • A ssemblin g and Han g in g th e Fan (Low Prof i le O nly) You can assemble your fan for standard or angled mounting as shown in Steps 4-1 – 4-6 on the previous page. For low profile mounting (ceilings less than 8 feet high), see Steps 4-7 – 4-11 on thi...

Page 9 - •Wirin g th e Fan

9 45034-01 • 10/23/08 • Hunter Fan Company All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national a...

Page 10 - • Inst al lin g th e C anopy and C anopy Trim Rin g

10 45034-01 • 10/23/08 • Hunter Fan Company 6-1. Partially install two canopy screws (about 2 full turns) in the hanger bracket. 6-2. Raise the canopy over the hanger bracket. Align partially installed screws with key slots in canopy. 6-3. Twist canopy clockwise to secure.6-4. Install third & fo...

Page 11 - -2. Feed the upper plug connector through the center; • Completin g Your Inst al l ation With a Bow l Li g ht Fi xture

11 45034-01 • 10/23/08 • Hunter Fan Company Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the upper switch housing, partially install two housing assembly screws into the switch housing mounting plate...

Page 13 - Installing the Glass Bowl; -9. Thread the pull chains through the

13 45034-01 • 10/23/08 • Hunter Fan Company Installing the Glass Bowl 7-9. Thread the pull chains through the outer holes in the light kit. 7-10. Attach the extra pull chains (included) to the fan pull chain and light pull chain using the plastic breakaway connector. (You may find the plastic breaka...

Page 14 - • The chain uses a breakaway connector that separates if the; To Change Airflow Direction; • O p eratin g and Cleanin g Your C ei lin g Fan

14 45034-01 • 10/23/08 • Hunter Fan Company In warm weather , use downward air flow pattern In cold weather , use upward air flow pattern 8-1. Turn on electrical power to the fan.8-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Of...

Page 15 - Problem: Lights dim when turned on or do not turn on; Check to make sure the wattage and type of light bulbs; • Trouble sho otin g

15 45034-01 • 10/23/08 • Hunter Fan Company Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker.2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing.4. Push motor reversing switch...