Huffy MQX-2150 - Manuals - manualsarea.com

Page 2 - WARNING

2 P/N 211994B 05/03 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or...

Page 3 - SAFETY INSTRUCTIONS; MOVING SYSTEM; HEIGHT ADJUSTMENT

05/03 P/N 211994B 3 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble th...

Page 5 - FRONT

05/03 P/N 211994B 5 Get to know the basic parts of your basketball system..... STRUTS BACKBOARD FRONT RIM WHEEL CARRIAGE ASSEMBLY BASE POLE

Page 6 - Description

6 P/N 211994B 05/03 PARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 206645 Tank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 900060 Top Pole Section 5 1 908480 Middle Pole Section with Label 6 1 908490 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 2028...

Page 7 - HARDWARE IDENTIFIER

05/03 P/N 211994B 7 HARDWARE IDENTIFIER Item #14 (1) Item #12 (6) Item #10 (1) Item #19 (12) Item #16 (2) Item #17 (6) Item #21 (4) Item #28 (2) Item #22 (4) Item #23 (2) Item #8 (1) Item #11 (1) Item #7 (1)

Page 8 - ASSEMBLE THE BASE

8 P/N 211994B 05/03 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION A: ASSEMBLE THE BASE 9/16” and 1/2” 9/16” and 1/2” AND/OR This is what your system will look likewhen you’ve finished this section: Item #14 (1) Item #12 (6) Item #10 (1) Item #16 (2) Item #17...

Page 10 - While maintaining alignment, bounce

10 P/N 211994B 05/03 4 5 6 WOOD SCRAP 4. IMPORTANT! Center the alignment slot of lower pole section (6) in the lowerhole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using woodscrap as shown until th...

Page 13 - ASSEMBLE THE BOARD AND RIM

05/03 P/N 211994B 13 TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BOARD AND RIM 1/2” 1/2” AND/OR This is what your system will look likewhen you’ve finished this section: Item #19 (12) Item #17 (6) Item #21 (4) Item #22 (4) Item #23 (2)

Page 14 - Final adjustments will be made in Step 3 of this section; Refer To

14 P/N 211994B 05/03 21 22 22 18 20 17 17 Mount brackets (20) and rim (18) to backboard and finger tighten as shown. NOTE: Final adjustments will be made in Step 3 of this section IMPORTANT! For spring loaded rim assembly, refer to instructionsincluded with rim hardware. 1. Refer To Instructions Inc...

Page 16 - Push second “arm” back and into ram as shown.

16 P/N 211994B 05/03 4. Install clips. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clipslightly so that second “arm” slides over the top of the first “arm”as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. Twist “body”...

Page 17 - Insert net into bottom of clip as shown.; NET INSTALLATION

05/03 P/N 211994B 17 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INSTALLATION 9. 18 19 25

Page 18 - APPLY HEIGHT AND MOVING LABEL & SECURING SYSTEM

18 P/N 211994B 05/03 15 1. 10 feet (3.05 m) Carefully upright assembly. Apply moving system label (15) to front of pole asshown. Regulation rim height is 10 feet (3.05 m). TWO PEOPLEREQUIRED FOR THISPROCEDURE. FAILURETO FOLLOW THISWARNING COULDRESULT IN SERIOUSINJURY AND/ORPROPERTY DAMAGE. WARNING! ...