Huffy In-Ground Basketball - Manuals

Page 2 - BEFORE YOU START; NOTE: Not all items pictured are included with every model.; MOVING SYSTEM; NOTICE TO ASSEMBLERS

2 ID# M6809011 12/06 BEFORE YOU START To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular...

Page 3 - SAFETY INSTRUCTIONS; over unexpectedly; Use caution when using this unit.

12/06 ID# M6809011 3 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble t...

Page 5 - PARTS LIST - See Hardware Identifier; NOTE; Hardware kit is designed for more than one

12/06 ID# M6809011 5 Item Qty. Part No. Description 1 1 600053 Tank 2 2 906410 Strut, Pole to Base 3 1 800344 Screw Jack Assembly 4 1 FR908402 Top Pole Section 5 1 FR908401 Middle Pole Section 6 1 FR908403 Bottom Pole Section 7 2 800332 Wheel Bracket 8 2 600056 Wheel, 3.5” 9 1 108306 Rod, Axle 10 2 ...

Page 8 - TOOLS REQUIRED FOR THIS SECTION; SECTION A: ASSEMBLE THE BASE

8 ID# M6809011 12/06 7 8 8 9 13 13 Complete wheel assembly as shown in Figure A. Secure wheel bracket (7) and wheel assembly (Fig. A.)to the tank (1) with a bolts (18) and washers (24). Repeat procedure for opposite wheel. 24 24 18 TO INSTALL SECONDPUSHNUT: • Assemble Pushnut, Wheels, Axle, AndWheel...

Page 9 - reference point in the next step.; NOTE ORIENTATION OF

12/06 ID# M6809011 9 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. 2. 4 6 BOTTOM TOP 5 MIDDLE IDENTIFICATION STICKER IDENTIFICATION STICKER Bounce middle pole section (5) into top section (4) using a wood scrap as ...

Page 10 - Wood Scrap

10 ID# M6809011 12/06 4. 4 5 6 Bounce top and middle pole assembly (4 and 5)onto bottom pole section (6) using a wood scrap asshown. Bounce until the top and middle poleassembly no longer moves toward the poleidentification mark on the bottom pole. Wood Scrap (not supplied) 5. Attach pole assembly t...

Page 12 - DO NOT OVER; Struts MUST be attached to

12 ID# M6809011 12/06 8. 42 6 14 16 15 IMPORTANT! DO NOT OVER TIGHTEN! 7. 2 2 40 2 2 24 40 24 49 14 49 14 IMPORTANT! DO NOT TIGHTENCOMPLETELY. TWO CAPABLE ADULTSREQUIRED FOR THISPROCEDURE. FAILURE TOFOLLOW THIS WARNING COULDRESULT IN SERIOUS INJURYAND/OR PROPERTY DAMAGE. WARNING! Rotate non-secured ...

Page 13 - COMPLETED ASSEMBLY

12/06 ID# M6809011 13 Securely rest the assembly on sawhorse. Identify elevator tubes (32 and 35). 35 32 9. Lower Elevator tube Upper Elevator tube 32 35 Toward Pole Toward Board 4 32 35 29 35 32 30 31 31 30 30 30 COMPLETED ASSEMBLY 29 38 TWO CAPABLE ADULTSREQUIRED FOR THISPROCEDURE. FAILURE TOFOLLO...

Page 17 - Note orientation of handle.

12/06 ID# M6809011 17 4 29 3 31 4. Place cover (17) onto screw-jack assembly (3). Install cap (11). 36 36 IMPORTANT! Note orientation of handle. 11 17 3 TIGHTEN BOLT (29) INLOCK NUT (31) UNTILFLUSH (EVEN) WITH LOCKNUT’S OUTER EDGE. WARNING! A. B. Install handle assembly (3, 17 and 11) to lower eleva...

Page 20 - RIM COVER ATTACHMENT

20 ID# M6809011 12/06 Apply Height Adjustment and Moving Label (33) to front ofpole, where it is clearly visible. 7. 8. B. D. C. A. Installnet (43). 568090 11/06 1 3 2 MOVING SYSTEM HEIGHT ADJUSTMENT 1. While holding pole, rotate basketball sytem forward until wheels engage with ground. 2. Move bask...