Huawei V200R001 - Manuals - manualsarea.com

VRP User Manual – Configuration Guide Volume 3 Manual Version T2-080168-20011213-C-1.5 Product Version V200R001 BOM 31010868 Copyright © 2001 by Huawei Technologies Co., Ltd. All Rights Reserved No part of this document may be reproduced or transmitted in any form or by anymeans without prior writte...

Page 3 - About This Manual; Contents

About This Manual Contents To help readers to better understand, use and maintain Quidway series routers, we publishthe manual suit of Quidway series routers. This manual suit includes: VRP User Manual Configuration Guide (V1.5) -Volume 1 VRP User Manual Configuration Guide (V1.5) - Volume 2 VRP Use...

Page 4 - Keyboard operation; Format; Mouse operation

Module 10 DDR Configuration (10DC) This module mainly introduces the principle and specific configuration of dial solutionsprovided by VRP1.5, including Legacy DDR configuration, Dialer Profile configuration andmodem management configuration. Module 11 VoIP Configuration (11VC) This module mainly in...

Page 5 - Symbol; Notify the special attention that should be

Action Description Click Press the left button or right button quickly (left button bydefault). Double Click Press the left button twice continuously and quickly. Drag Press and hold the left button and drag it to a certain position. Symbol Some distinct symbols are employed in the manual to indicat...

Page 6 - HUAWEI; VRP

HUAWEI ® VRP User Manual – Configuration Guide Volume 3 11 – VoIP Configuration (VC)

Page 7 - Chapter 2; Chapter 2 IP Fax Configuration; Overview to IP Fax; The diagram of IP Fax architecture is as follows:; Architecture of IP Fax; Configuring IP Fax

User Manual - Configuration Guide (Volume 3) Versatile Routing Platform Chapter 2 IP Fax Configuration 2-1 Chapter 2 IP Fax Configuration 2.1 Overview to IP Fax Traditional faxes are sent and received over PSTN. Today fax services are widely useddue to its advantages, such as many kinds of transmiss...

Page 8 - Checking If Configuring Fax to Use ECM Mode; Check if configuring fax to use ECM mode; fax-relay ecm disable; no fax-relay ecm disable

User Manual - Configuration Guide (Volume 3) Versatile Routing Platform Chapter 2 IP Fax Configuration 2-2 IP telephone works after VoIP is configured. Generally speaking, faxes can now besent and received by using the default configuration of IP Fax only after a facsimilemachine is connected. The p...

Page 9 - voice; ”), the highest allowable rate of fax should; By default, the fax rate will be determined by voice mode.; local

User Manual - Configuration Guide (Volume 3) Versatile Routing Platform Chapter 2 IP Fax Configuration 2-3 If it is set to be the values except for “disable” and “voice”, the fax rate shall be set to bethe corresponding values. The rate set here is not specified rate but the highestallowable rate. W...

Page 10 - Configuring Gateway Carrier Transmit Energy Level; Configure gateway carrier transmit energy level; Configure sending redundancy packet number of T38 fax protocol

User Manual - Configuration Guide (Volume 3) Versatile Routing Platform Chapter 2 IP Fax Configuration 2-4 received “1” is less than the preset threshold value, then the current rate train issuccessful, otherwise, it is not successful. Please perform the following configuration in dial peer configur...

Page 11 - Operation; intercommunicates with the gateway of VocalTec.; rtp; Monitoring and Maintenance of IP Fax

User Manual - Configuration Guide (Volume 3) Versatile Routing Platform Chapter 2 IP Fax Configuration 2-5 By default, the number for sending two kinds of redundancy packet is 0.Theredundancy packet number for sending low-speed data ranges from 0 to 5, and theredundancy packet number for sending hig...

Page 12 - Monitoring and maintenance of IP Fax; Typical Configuration of IP Fax; ) Networking Requirements; Internet; Networking diagram for typical IP fax configuration

User Manual - Configuration Guide (Volume 3) Versatile Routing Platform Chapter 2 IP Fax Configuration 2-6 Table VC-2-9 Monitoring and maintenance of IP Fax Operation Command Open all of the debugging information switches of ipfax debug ipfax all Open the debugging information switch of function api...

Page 13 - The parameter settings for the router in Shenzhen is as follows:

User Manual - Configuration Guide (Volume 3) Versatile Routing Platform Chapter 2 IP Fax Configuration 2-7 Quidway(config-peer-voip1)# dial-peer voice 2 pots Quidway(config-peer-pots2)# destination 0101002 Quidway(config-peer-pots2)# port 2 The parameter settings for the router in Shenzhen is as fol...