Hoover Upright Bagless Vacuum Cleane- Manuals

Handle position For ease in sliding knob, place handlein the upright position (C). The nozzle will not move into theadjusted position until the cleanerhandle is lowered to the operatingposition (D). Settings For maximum cleaning performance, the following carpet height settings arerecommended. • Low...

7 Cleaning lightweightflexible rugs Stand on one end of rug and movecleaner toward other end or edge. Before reaching edge, push down onhandle. This will lift up the nozzle (frontof cleaner) as shown and will preventrug from clinging to cleaner. Continue tolift up nozzle so that when you havereached...

3. Maintenance When to empty It is recommended that the dirt cup beemptied before the dirt reaches the dirtopening on back of dirt cup (Fig. 3-1) orafter every use if preferred. CAUTION: Very fine materials, suchas face powder or cornstarch, mayseal the filter and cause loss of suc-tion. When using ...

9 3-10 3-6 3-5 3-7 3-8 3-9 3-11 Pull up on pre-filter assembly. Slide it outof cup. Replace dirt cup. Filter assembly How to clean filterassembly Remove dirt cup and dirt cup lid asdescribed in “How to empty dirt cup”. Pivot pre-filter assembly toward center ofcup. Remove main filter from pre-filter...

G Remove lens - Disconnect clean- er from electrical outlet. Using a screwdriver, remove the twoscrews as shown and lift off lens. 3-16 3-15 10 Secondary and finalfilters Cleaning secondary filter Disconnect cleaner from electricaloutlet. The secondary filter (G) , located under- neath the retainer ...

11 Continued ➜ 3-17 3-18 Remove agitator brush roll Remove agitator and used belt. Discard used belt. Replace lens - Reposition lens and secure with the two screws. How to replace Disconnect cleaner from electricaloutlet. Remove bottom plate Place handle in low position and turncleaner over so botto...

12 Service To obtain approved HOOVER serviceand genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: • checking the Yellow Pages under “Vacuum Cleaners - Household” OR - • checking the list of Factory Service Centers provided...

13 Clearing blockages Disconnect cleaner from electricaloutlet. Low suction or pick up may be due to ablockage in the system. Refer to the fol-lowing steps to check for blockages continuing with each step until theblockage is found: Turn cleaner OFF and disconnect fromelectrical outlet.1. Check full...

Handle position For ease in sliding knob, place handlein the upright position (C). The nozzle will not move into theadjusted position until the cleanerhandle is lowered to the operatingposition (D). Settings For maximum cleaning performance, the following carpet height settings arerecommended. • Low...

7 Cleaning lightweightflexible rugs Stand on one end of rug and movecleaner toward other end or edge. Before reaching edge, push down onhandle. This will lift up the nozzle (frontof cleaner) as shown and will preventrug from clinging to cleaner. Continue tolift up nozzle so that when you havereached...

3. Maintenance When to empty It is recommended that the dirt cup beemptied before the dirt reaches the dirtopening on back of dirt cup (Fig. 3-1) orafter every use if preferred. CAUTION: Very fine materials, suchas face powder or cornstarch, mayseal the filter and cause loss of suc-tion. When using ...

9 3-10 3-6 3-5 3-7 3-8 3-9 3-11 Pull up on pre-filter assembly. Slide it outof cup. Replace dirt cup. Filter assembly How to clean filterassembly Remove dirt cup and dirt cup lid asdescribed in “How to empty dirt cup”. Pivot pre-filter assembly toward center ofcup. Remove main filter from pre-filter...

G Remove lens - Disconnect clean- er from electrical outlet. Using a screwdriver, remove the twoscrews as shown and lift off lens. 3-16 3-15 10 Secondary and finalfilters Cleaning secondary filter Disconnect cleaner from electricaloutlet. The secondary filter (G) , located under- neath the retainer ...

11 Continued ➜ 3-17 3-18 Remove agitator brush roll Remove agitator and used belt. Discard used belt. Replace lens - Reposition lens and secure with the two screws. How to replace Disconnect cleaner from electricaloutlet. Remove bottom plate Place handle in low position and turncleaner over so botto...

12 Service To obtain approved HOOVER serviceand genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: • checking the Yellow Pages under “Vacuum Cleaners - Household” OR - • checking the list of Factory Service Centers provided...

13 Clearing blockages Disconnect cleaner from electricaloutlet. Low suction or pick up may be due to ablockage in the system. Refer to the fol-lowing steps to check for blockages continuing with each step until theblockage is found: Turn cleaner OFF and disconnect fromelectrical outlet.1. Check full...