Hoover QS Quiet- Manuals

How to assemble 1. Connect hose To connect hose, insert hose into opening of cleaner lining up the ar- row on the hose with the dot on the cleaner. Turn the hose clock-wise until it lines up with the bar on the cleaner and latch locks intoplace. When the hose is attached proper- ly, the hose cord pl...

How to use Handle adjustments The handle has two positions when used with the power noz- zle: Upright and Operating. To lower handle to the Operating position, place your foot on the power nozzle and push the han- dle down. Automatic nozzle adjustment The power nozzle adjusts auto- matically to effe...

Nozzle connector Removing larger items from carpet and floor surfaces before vacuuming will help maintain the cleaning effectiveness of your cleaner. However, if loss of suction power should occur, proceed as follows: make sure Suction Regulator is closed; check bag for fullness and make sure folds ...

To connect and remove tools To connect the tools, insert end of tool into the extension wand andsnap into position. To disconnect, press down on the center of the spring latch and remove tool. Tools may also be attached to the handle by rotating the plastic latch ring to accept the button projec- ti...

Maintenance The following sections are concerned with proper maintence of the clean-er. Familiarize yourself with these home maintenance tasks and keep thisowner’s manual in a convenient place where you can refer to it when need-ed. Proper use and care of your cleaner will insure continued cleaning ...

SECONDARY FILTER To clean secondary filter Disconnect cleaner from elec- trical outlet. The secondary filter protects the motor from dirt particles. If the fil- ter becomes dirty, either clean or replace it. To remove secondary filter, open cover of cleaner and lift the filter from the top of the mo...

AGITATOR BRUSHES When to replace brushes To check condition of brushes, place edge of a card on the bot- tom of nozzle base, across agita- tor opening. Rotate agitator by hand. If brushes do not touch edge of card, all four brushes andbrush roll should be replaced to maintain cleaning effectiveness....

3. Note position of bar-brush as- . semblies to insure correct replace- ment. Remove bar-brush assemblies by pulling them from agitator slots. Use pliers if necessary. The word “BAR” is stamped near the slots on the agitator. Match the bar side of the bar brush assembly with the label on the agitato...

ser check list This appliance was inspected thoroughly and was in good operating condi- tion when it was shipped from the factory. If a minor problem develops, it usually can be remedied quite easily when the cause is identified. Accord-ingly, this check list is provided for your convenience. Proble...

VCMA VACUUM CLEANER MANUFACTURERS ASSOCIATION (HOOVER AN ASSOCIATION MEMBER) Service To The Consumer Since 19 13 This information has been compiled by the Vacuum Cleaner Manufacturers Associ- ation from Governmental and Private Sources concerned with product safety. These basic guidelines are for yo...

How to assemble 1. Connect hose To connect hose, insert hose into opening of cleaner lining up the ar- row on the hose with the dot on the cleaner. Turn the hose clock-wise until it lines up with the bar on the cleaner and latch locks intoplace. When the hose is attached proper- ly, the hose cord pl...

How to use Handle adjustments The handle has two positions when used with the power noz- zle: Upright and Operating. To lower handle to the Operating position, place your foot on the power nozzle and push the han- dle down. Automatic nozzle adjustment The power nozzle adjusts auto- matically to effe...

Nozzle connector Removing larger items from carpet and floor surfaces before vacuuming will help maintain the cleaning effectiveness of your cleaner. However, if loss of suction power should occur, proceed as follows: make sure Suction Regulator is closed; check bag for fullness and make sure folds ...

To connect and remove tools To connect the tools, insert end of tool into the extension wand andsnap into position. To disconnect, press down on the center of the spring latch and remove tool. Tools may also be attached to the handle by rotating the plastic latch ring to accept the button projec- ti...

Maintenance The following sections are concerned with proper maintence of the clean-er. Familiarize yourself with these home maintenance tasks and keep thisowner’s manual in a convenient place where you can refer to it when need-ed. Proper use and care of your cleaner will insure continued cleaning ...

SECONDARY FILTER To clean secondary filter Disconnect cleaner from elec- trical outlet. The secondary filter protects the motor from dirt particles. If the fil- ter becomes dirty, either clean or replace it. To remove secondary filter, open cover of cleaner and lift the filter from the top of the mo...

AGITATOR BRUSHES When to replace brushes To check condition of brushes, place edge of a card on the bot- tom of nozzle base, across agita- tor opening. Rotate agitator by hand. If brushes do not touch edge of card, all four brushes andbrush roll should be replaced to maintain cleaning effectiveness....

3. Note position of bar-brush as- . semblies to insure correct replace- ment. Remove bar-brush assemblies by pulling them from agitator slots. Use pliers if necessary. The word “BAR” is stamped near the slots on the agitator. Match the bar side of the bar brush assembly with the label on the agitato...

ser check list This appliance was inspected thoroughly and was in good operating condi- tion when it was shipped from the factory. If a minor problem develops, it usually can be remedied quite easily when the cause is identified. Accord-ingly, this check list is provided for your convenience. Proble...

VCMA VACUUM CLEANER MANUFACTURERS ASSOCIATION (HOOVER AN ASSOCIATION MEMBER) Service To The Consumer Since 19 13 This information has been compiled by the Vacuum Cleaner Manufacturers Associ- ation from Governmental and Private Sources concerned with product safety. These basic guidelines are for yo...