Hoover Canisfer Cleaner with Power Nozzle - Manuals

Page 4 - Unpacking

Unpacking Unpack cleaner from carton identify the parts shown. move and dispose of the car&board packing. Canister cleaner B. Power nozzle C. Paper bag D. Extension wands and hose The cleaner assembled will like the drawing below. A 0 C - 1 7- 1 8 3

Page 6 - How; to; assemble; Connect hose

How to assemble Connect hose Insert hose end with cord into opening of cleaner, lining up largest projection on hose with largest notch of opening. Turn hose to theright to tighten. When hose is attached properly, hose cord plug will reach toreceptacle on cleaner. Insert plug as deeply into the rece...

Page 8 - How to use; Power nozzle; positions; Edge cleaning

How to use Power nozzle The power nozzle adjusts automatically for cleaning hard surface floors and various heights of carpet. It is not recommended for very irregular surfaces such as brick, slate, and certain parquet floors unless it is unplugged from the cleaner. This will stop the agitator from ...

Page 9 - Cleaning tools

Cleaning tools The cleaning tools have many uses.Select the tool best suited for the cleaning task from the descriptions below. Adjust the suction regulator to select the amount of suction appropriate for the cleaning task. 1. Crevice tool may be used for radiators, dresser drawers, spacesbetween ki...

Page 10 - To clean stairs

To connect and remove tools To connect tools, insert end of tool into extension wand and snap into position. To disconnect, pressdown on the center of the spring latch and remove tool. Tools’attach to hand grip by rotating plastic ring until slots in theopening align. Insert tool and turn latch ring...

Page 11 - How to store; Maintenance; The bag; When to replace; Where to buy; What to buy

How to store Your cleaner can be stored on endas shown in the illustration. Storepower nozzle with handle in upright position. The hose and extension wands can be stored disassembled from thecleaner if desired. Maintenance The following sections are concerned with proper maintenance of the cleaner. ...

Page 12 - to replace

How to replace Disconnect cleaner from electrical outlet. 1. Remove cover by lifting top section of carrying handle and pulling forward. 2. Depress latch and lift out used bag. 3. Place lower notched edge ofnew bag collar into grooves locatedinside front of cleaner. 4. Pull collar forward until latc...

Page 13 - Clearing obstructions

Clearing obstructions Remove larger items from carpet and floor surfaces before vacuuming to help prevent obstructions in hose, wands or nozzle connector, and tomaintain cleaning effectiveness of your cleaner. To check for obstructions, first turncleaner off and disconnect from electrical outlet; th...

Page 14 - Secondary filter; How to clean; The belt

Secondary filter How to clean Disconnect cleaner from cai The secondary filter is located inside the cleaner behind the paperbag. To remove filter, first remove cover of cleaner, then lift out filter. Clean filter by rinsing it in water. When dry, slide filter back into position. Do not operate clea...

Page 16 - Agitator brush roll; How to replace

6. Position nozzle cover on front lip of nozzle base. Press cover into place. Turn nozzle over and replacescrews. Agitator brush roll When to replace Disconnect cleaner from electri- cal outlet. When agitator brushes are worn, the brush roll should be replaced. To check condition of brushes, move th...

Page 18 - Lubrication; If you have a problem

Lubrication The motor is equipped with bearings, which have been lubricated for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing. The agitator is equipped with two ball bearings that should be lubricated periodically by a Ho...

Page 19 - Service

Service If the problem persists, check the Yellow Pages of your telephone book under “Vacuum Cleaners-Household” for your nearest Hoover Factory Service Center or Authorized Warranty Dealer where approved HOOVER service and genuine HOOVER replacement parts may be obtained. Provided with this product...