Hoover 41016047 - Manuals

Hoover 41016047 – Manual in PDF format online.

Manuals:

Manual

Manual Hoover 41016047

Summary

Page 2 - • INSTALLATION; CONTENTS

2 UNPACKING THE APPLIANCE Inside the appliance, you will find : • a plastic bag containing :- the new jets for the gas modification, if required,- according to model, a cylindrical connector and/or a conical connector with sealfor the gas connection,- the fixing brackets with screws required for ins...

Page 3 - (located under the lower casing of the hob); HOB FEATURES

3 . Rating plate (located under the lower casing of the hob) • All accessible parts of the hob will become hot while in operation. Always keep childrenaway from it.• The hob should be given a quick clean after each use, to avoid the accumulation ofspillages and grease. If spillages are not removed, ...

Page 4 - Before installing the hob :; INSTALLATION

4 Before installing the hob : make sure that the appliance is compatible with the gas supply source.The hob is pre-set in the factory to work with the type of gas shown on the packingand the plate attached to it.Natural gas G 20-20 mbar / G 25-25 mbar : mains gas if necessary, adapt the hob for use ...

Page 5 - INSTALLATION: «GAS CONNECTION»; CHANGING THE JETS; fit the correct jet for the; Each jet is designated by size.; CHANGING THE GAS TYPE :; the calorific power output and gas pressure will

5 ¤ = Factory setting: Natural gas = G20-20 mbar / G25-25 mbar X = Gas setting possible according to installation Butane gas G30-29 mbar or Propane gas G 31-37 mbar INSTALLATION: «GAS CONNECTION» CHANGING THE JETS To gain access to the jets, remove the pan supports,and remove the burner cap and body...

Page 6 - SEAL

6 Both the worktop where the hob will be fitted and any adjacent kitchen furniture must bemade from heat resistant material and fixed with heat resistant adhesive.If, when installing the hob, the lower hob face is adjacent to an area normally accessiblewhen handling or cleaning, fit a heatproof part...

Page 7 - POSSIBLES MEANS OF CONNECTION :

7 INSTALLATION: «GAS CONNECTION» The hob can be built-in ; it is in class 3 (in compliance with gas regulations EN 30.1.1) ;adjoining furniture should not be higher than the level of the hob.This appliance is not connected to an evacuation device for the products of combustion.It must be installed a...

Page 8 - INSTALLATION: «ELECTRICAL CONNECTION»

8 INSTALLATION: «ELECTRICAL CONNECTION» The mains electricity supply connected to the appliance should comply with the norms inforce in the country of installation. Connection to the mains electricity supply should be through a socket with an earthterminal, or through an intermediary switching devic...

Page 9 - • SETTING THE IDLE FLAME; By-pass screw of the hob burner; REGULATING THE MINIMUM FLAME ON THE HOB BURNER; INSTALLATION: «REGULATING THE FLAME»

9 • SETTING THE IDLE FLAME If you have changed the type of gas, it is important to verify the flame stability at theminimum regulation. «Gaining access to the by-pass screw»To gain access to hob burner by-pass screws, remove the knobs from the control panel. By-pass screw of the hob burner Never loo...

Page 10 - Ø 18 cm and more; THE GAS BURNER

10 THE ULTRA-RAPID BURNER or "4 RINGS" BURNER, power rating 3,5 kW :use this burner for bringing to boil, for cooking large quantities, and generally for all foodsrequiring rapid cooking.THE FAST BURNER, power rating 2,5 kW :use the large burner for all foods requiring rapid cooking.THE SEMI...

Page 11 - which in turn ignite the burner.; Hob; • To turn the flame out, turn the control knob back to stop position.

11 Each burner is fitted with automatic ignition. The ignition can be made with one hand,while you have the pan in the other hand. USE : • Turn on the gas tap, • A symbol next to each control knobindicates which burner is lit.(example: front left burner) • Hob with automatic ignition integrated : • ...

Page 12 - THE HOT PLATE; BEFORE USING THE ELECTRICAL HOT PLATE :; • An indicator light comes on to show that the hot plate is operating.; DIFFERENT TEMPERATURE SETTINGS :

12 THE HOT PLATE THE SPEED PROTECTED HOT PLATE - 1500 W. This is a cast-iron hot plate, controlled by a 7 position switch.An internal thermostat cuts off part of the power supply if overheating occurs. (if, forexample, a hot plate is working without a pan on it). BEFORE USING THE ELECTRICAL HOT PLAT...

Page 13 - Cooking with the electrical hot plate

13 Cooking with the electrical hot plate To get the best results from your appliance it is important to observe the following : • Use thick, flat-based cooking vessel :a completely flat base prevents overheating to certain parts which causes food to stick.Thick metal allows for good heat distributio...

Page 14 - CLEANING AND MAINTENANCE; MAINTENANCE OF THE GLASS HOB

14 CLEANING AND MAINTENANCE 30˚maxi Racloir Scraper Before cleaning or removing the hob, it is imperative to :• disconnect the hob from the mains supply,• let all parts of the hob cool down. Never use harsh abrasives, scouring pads or sharp objects to clean the hob.Do not use a sponge that it is exc...

Page 15 - THE KNOBS

15 Pan support Burner head Burner cap • Burner caps and pan supports : the pan support is made of enamelled cast-iron and theburner cap is made of enamelled steel, for a maximal protection and an easy cleaning.They are simply placed. Just lift them off and clean with a damp, slightly soapy sponge.Do...