Hobart ML-104586 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS

– 2 – © HOBART CORPORATION, 1995 TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking . . . . . . . . . . . . . . . . ...

Page 3 - MODEL FP350 FOOD PROCESSOR; SAVE THESE INSTRUCTIONS; GENERAL; UNPACKING; : THE ELECTRICAL CORD HAS A THREE-PRONGED GROUNDING PLUG WHICH

– 3 – Installation, Operation, and Care of MODEL FP350 FOOD PROCESSOR SAVE THESE INSTRUCTIONS GENERAL The FP350 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicingvegetables, fruits, or cheese. A worktable, a wall rack, and a wide range of slicer, shredder, and dicing...

Page 5 - OPERATION; WARNING; ROTATING KNIVES INSIDE. ALWAYS USE PUSHER PLATE. KEEP HANDS OUT; CONTROLS

– 5 – OPERATION WARNING : ROTATING KNIVES INSIDE. ALWAYS USE PUSHER PLATE. KEEP HANDS OUT . Proper assembly of the FP350, including selection of the appropriate cutters, is necessary for correctoperation of the food processor. Refer to the Cutting Tool Guide for sizes of cutters and refer to theappr...

Page 7 - Removing the Cutting Tools; cylinder is set in the open position.; USING THE FEED CYLINDER

– 7 – Removing the Cutting Tools 1. Using the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 2. Turn the lock handle counterclockwise and swing the feed cylinder out to the right. 3. Using the wrench supplied, loosen th...

Page 8 - Do not leave the cutting blades in a wet condition when not in use.

– 8 – CLEANING WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING. Clean the machine immediately after each use. Dismantle all removable parts from the machine andwash them in warm water and detergent. Rinse thoroughly and wipe dry with a soft clean cloth. Allowing food ju...

Page 9 - CUTTING TOOL GUIDE; Fractional sizes are in inches (millimeters are in parentheses).; Slicers; Use Fine and Standard Slicers for sliced products and for dicing.

– 9 – CUTTING TOOL GUIDE Fractional sizes are in inches (millimeters are in parentheses). Slicers Use Fine and Standard Slicers for sliced products and for dicing. Soft products like tomato - use the FINE SLICER, not the STANDARD SLICER. FINE SLICER 1 ⁄ 16 (1.5 mm) FINE SLICER 1 ⁄ 8 (3 mm) FINE SLIC...

Page 11 - MAINTENANCE; : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING; REPLACEMENT DICING GRIDS; TROUBLESHOOTING

– 11 – MAINTENANCE WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to make sure that it is in proper working order. Plates must be clean,intact and sharp. The knife shaft should be regularly lubricated with a drop of mineral o...

Page 12 - SERVICE

– 12 – FORM 19353 Rev. D (Oct. 2000) PRINTED IN U.S.A. SERVICE Contact your local Hobart Service Office for any repairs or adjustments needed on this equipment.Long-term service contracts are available on this and other Hobart products. SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION Low output or bad cutti...