Hobart LXiH ML-130017 - Manuals

Page 3 - TABLE OF CONTENTS

– 3 – TABLE OF CONTENTS GENERAL ............................................................................................................................................ 4 INSTALLATION ...................................................................................................................

Page 4 - SAVE THESE INSTRUCTIONS; GENERAL; MODEL

– 4 – Installation, Operation and Care of LXi SERIES DISHWASHERS SAVE THESE INSTRUCTIONS GENERAL The LXi Series dishwashers are fully automatic, front-loading dishwashing machines that are capableof 30 racks per hour. All LXi Series dishwashers shut down automatically 4 hours after last use to conse...

Page 5 - INSTALLATION; UNPACKING; ater

– 5 – INSTALLATION UNPACKING Immediately after unpacking the dishwasher, check for possible shipping damage. If this machine isfound to be damaged, save packaging material and contact the carrier within 15 days of delivery. LOCATION Prior to installation, verify that the electrical supply agrees wit...

Page 7 - Use stranded copper wire suitable for at least 90

– 7 – ELECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THEAPPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCALELECTRICAL CODES. WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOWLOCKOUT / TAGOUT PROCEDURES. ELECTRICAL DATA Complie...

Page 9 - OPERATOR PROGRAMMING MODE; To being the process start with the machine off.

– 9 – OPERATOR PROGRAMMING MODE The Operator Programming mode allows changes to be made from factory settings to the chemicalpumps’ operation. This includes the Detergent and Rinse Aid pumps, but does not apply to the Sanitizerpump on the LXiC and LXiGC models. The Detergent and/or Rinse Aid pumps c...

Page 12 - OPERATION; BEFORE FIRST USE

– 12 – CHEMICAL SANITIZER (LXiC AND LXiGC) CAUTION: Items such as pewter, aluminum and silver will be attacked by sodium hypochlorite(bleach). Therefore, chemical-sanitizing dishwashers should not be used to wash such items. On model LXiC only, the chemical sanitizer pump is factory-set for use with...

Page 13 - OPERATING THE LXi DISHWASHER

– 13 – OPERATING THE LXi DISHWASHER S I H T O D S W O H S Y A L P S I D S K R A M E R . N O s s e r P . r e b m u n l e d o M s i h T . k c e h c - f l e s s m r o f r e p r e h s a w h s i D . s d n o c e s 0 1 - 5 s e k a t e r u t a r e p m e t p m u s d n a t il L L I F s i e n i h c a m n e h w...

Page 14 - DIAGNOSTIC MESSAGES

– 14 – DIAGNOSTIC MESSAGES In the event of a problem with a temperature probe, the display will flash P1, P2 or P3 every second.The respective heaters will shut down. Other functions will continue to operate normally. Contact yourlocal Hobart Service Office. Drain and fill error messages are display...

Page 15 - PREPARATION

– 15 – PREPARATION Make sure the coarse (Fig. 7) and fine (Fig. 8) strainers are in place and free of debris. Check both washarms and rinse arms to make sure they spin freely and are not clogged. Fig. 7 Fig. 8 Dishes must be scraped and/or rinsed to remove food particles and other debris. Never use ...

Page 17 - CLEANING; Remove the lower rinse arm by unscrewing the

– 17 – CLEANING This machine must be cleaned at least once each working day. Use only products formulated to be safeon stainless steel. 1. Press OFF. The machine will drain. When the display is no longer lit, open the door and removeany debris from the bottom of the tank. Do notallow food soil to ac...

Page 18 - PRIMING CHEMICAL PUMPS; The priming operation can be reset by either:

– 18 – PRIMING CHEMICAL PUMPS When a chemical becomes empty, the priming operation starts automatically the next time the machineis turned on or a wash cycle is started. This feature is only supported on machines with the chemicalsense board installed and where CHEMICAL SENSING is enabled. Note that...

Page 19 - MAINTENANCE; DELIMING; Press OFF to power down the dishwasher.; LUBRICATION

– 19 – MAINTENANCE DELIMING WARNING: DELIMING SOLUTION, RINSE AGENTS OR ANY OTHER KIND OF ACID MUST NOTCOME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED INCHEMICAL-SANITIZING MACHINES. MIXING MAY CAUSE HAZARDOUS GAS TO FORM. THISENTIRE PROCEDURE MUST BE FOLLOWED STEP BY STEP FOR S...

Page 20 - TROUBLESHOOTING

– 20 – TROUBLESHOOTING This section outlines various symptoms and possible causes that may be encountered in the event ofabnormal machine operation. If symptoms persist after possible causes have been checked, servicemay be required. Symptom Possible Causes No machine operation 1. Machine OFF - turn...

Page 23 - NOTES