Hobart HGC40D & HGC60D - Manuals

– 6 – ASSEMBLING THE LEGS TO THE OVEN Unpack the oven and leg set. Position oven on its back, taking care not to scratch or damage it. The gas pipe connection protrudesbeyond the back; provide for this when oven is tipped back by resting it on suitable spacers (2 x 4's etc.). Attach each of the four...

– 7 – Move the oven with legs to the installed position and place the upper oven on top of the lower oven usingthe locating studs. Remove the rear panels from both ovens. Remove the right angle flue extension (Fig. 3) from the topoven. Insert the right angle short flue extension into the top oven. I...

– 8 – ELECTRICAL CONNECTIONS WARNING: THE POWER CORD IS PROVIDED WITH A GROUNDING PLUG. THE OUTLET TOWHICH THIS PLUG IS CONNECTED MUST BE PROPERLY GROUNDED. IF THE RECEPTACLE ISNOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THEGROUNDING PRONG FROM THIS PLUG. Your gas convection...

– 9 – Gas Pressures and Orifices Natural Gas The burner orifices are sized to deliver the nameplate input rating (40,000 Btu/hr) at a gas manifoldpressure of 3.5" W.C (0.8 kPa). The gas pressure regulator is integral to the gas solenoid valveand is factory set to supply 3.5" W.C. (0.8 kPa) a...

– 10 – OPERATION CONTROLS — MODELS DGC1 & HGC40/HGC60 (Fig. 4) ON / OFF / COOLDOWN SWITCH — ON — turns oven control circuits on. OFF — turns oven control circuits off.COOLDOWN — allows the fan motor to run with the doorsajar to speed oven cooling. 2-SPEED FAN SWITCH — HI / LO — Adjusts air veloc...

– 11 – LIGHTING THE DGC1 AND HGC40/HGC60 OVENS Turn manual gas valve ON. Turn ON/OFF/COOLDOWN switch ON and turn thermostat to its maximumsetting. Both the ON and HEAT lights should come on. If HEAT light is not on, make sure door is closed. After 5 seconds, the spark ignition system will start and ...

– 12 – CONTROLS — MODEL HGC40D/HGC60D (Fig. 5) MODEL HGC40D/HGC60D Fig. 5 PL-51601 THERMOSTAT GAS VALVE 2 SPEED FAN - HI / LO LIGHT SWITCH TIMER TURN GAS VALVE "ON"PUSH MASTER SWITCH TO"ON" POSTION. IF OVENFAILS TO LIGHT. PUSHMASTER SWITCH TO "OFF"TURN GAS VALVE OFF WAIT5 MIN...

– 15 – Pulse Button Selects the pulse time setting. A cook time must be set first. The pulse time can thenbe set equal to or less than the cook time. The pulse time will be the portion of cook timeto operate in the pulse mode. Pulse mode will start first. When pulse time elapses, theremainder of the...

– 18 – COOK AND HOLD OPERATION Cook and Hold cooks the product in two stages. During First Stage Cooking, the oven temperature isregulated by the Cook thermostat for the amount of time set on the Cook Timer. After the lapsed timecounts down to 00:00, Second Stage Cooking begins. During Second Stage ...

– 20 – COOKING CHARTS Models DGC1, HGC40/HGC40D and HGC60/HGC60D BAKED PRODUCTS * Some people prefer high speed for darker cheese. ** Low speed will give you a more uniform color. Product Temps. Time (Min.) No. Shelves Fan Speed (°F) (°C) Sheet Cakes (5 lb. [2.3 kg] each) 300 (149) 30 5 Low Soda Bis...

– 21 – MEAT & FISH PRODUCTS MISCELLANEOUS PRODUCTS FOR BEST RESULTS Product to be cooked should be centered on the oven rack, and the racks should be spaced evenly within theoven cavity. It is best not to rotate the product or open the doors during the cooking cycle. Preheat oven to 50°F (10°C) ...

– 22 – MAINTENANCE WARNING: TURN OVEN OFF AND UNPLUG ELECTRICAL CORD BEFORE PERFORMING ANYMAINTENANCE. The fan motor comes with sealed bearings and requires no lubrication. The door mechanism requires occasional lubrication with mineral oil. If this oven is placed on casters, it should be connected ...

– 23 – TROUBLESHOOTING If NO IGNITION LIGHT remains lit for more than 20 seconds after three trials (Models DGC1 andHGC40), or E-05 displays after three trials (Model HGC40D): • Turn oven off for 5 minutes before attempting to relight. • Check gas supply valves to be sure they are open. • Check elec...

– 24 – FORM 19240 Rev. D (3-98) PRINTED IN U.S.A. NOTES